(c) Given a network with the load power shown in Figure Q3(c). Determine: (i) the supply voltage, Vs. the required capacitive element value in parallel with the 36 kW load to raise the power factor of this load to 0.9 (lagging). (ii) 0.12 jo.3 2 36 kW 24kW Vs (+ 0.88 pf lagging 24020° V rms 0.82 pf lagging Figure Q3(c)

(c) Given a network with the load power shown in Figure Q3(c). Determine: (i) the supply voltage, Vs. the required capacitive element value in parallel with the 36 kW load to raise the power factor of this load to 0.9 (lagging). (ii) 0.12 jo.3 2 36 kW 24kW Vs (+ 0.88 pf lagging 24020° V rms 0.82 pf lagging Figure Q3(c)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

chapter 1 Q1 The rms value the AC input voltage to the of Circuit shown is 230U, and the firing angle is maintained Current is 5 A. constant at 45° so that the load a) Calculate the de output voltage. b) Assume that the load resistance remains the a same, find the current is a FWD is used at the output. c) If^ prime prime ScR^ prime prime " is open circuited, find load voltage and current a is the Same) (FWD is still connected and high. "L Load Ans[146.4U,6.03A ; 3.c2A] 3 3 FWD
Problem 2 The circuit diagram of a certain load is presented below. Determine the following: a. The power factor of the load. b. If the load is connected across a 400 Vrms source, determine the real and reactive power consumed by the load. c. From (b), determine the value of the capacitor to be placed in parallel with the load in order to improve the power factor of the load to 95% lagging. From (b), A synchronous motor is installed in parallel with the load to correct the pf. The motor is rated 5 hp operating at 60% efficiency. Assuming that the motor is running at rated power. Determine the apparent power and power factor of the motor in order to improve the load's pf to 95% lagging. 202 500 µF HI + VL -20 mH 5Ω >0.5VL m 15 mH
Q2: Write a lecture for teaching the complex power fed to an (R-L) load fed from an AC power source of sinusoidal voltage and current waveforms, describing its three components, their waveforms, their power triangle, and units.
If the voltage and current supplied to a circuit orload by a source are˜VS = 170∠(−0.157) V ˜IS = 13∠0.28 Adeterminea. The power supplied by the source which isdissipated as heat or work in the circuit (load).b. The power stored in reactive components in thecircuit (load).c. The power factor angle and power factor.
Electrical load that draws current whose impedance varies throughout the cycle of the input ac voltage waveform is known as nonlinear load. True False
Find the voltage average and the voltage waveform for the output of the circuit shown below.
I need the answer as soon as possible
Question-2 Can you throw the emergency solution? I would appreciate it if you write legibly.
Two loads connected in parallel take a total of 2.4 kW with a lag fp of 0.8, from a line at 120 V rms and 60 Hz. of the loads absorbs 1.5kW with lagged fp of 0.707. Deter- mine: a) the fp of the second charge, b) the element in parallel required to correct the fp of the two charges and convert it to behind 0.9.
Which one of the following statements is true: The purpose of the power-factor correction is to add inductive elements to keep real power at a minimum level. The purpose of the power-factor correction is to add resistive elements (typically resistances) to improve the total reactive power. The purpose of the power-factor correction is to add reactive components (typically capacitive) to establish a system power factor closer to unity. The purpose of the power-factor correction is to add resistive elements (typically resistances) to establish a system power factor closer to zero.
In the figure below, all impedances are in ohms, all voltages are in volts and currents in Amperes. Both sources operate at 60 Hz. X, = 200 n X, = 600 n 80 sin (wt + T/2) x, = 600 2 0.2 ain wt Determine the time dependent current i (A) due to the current Choose... source Determine the time dependent current (A) flowing through the inductance with a Choose... reactance of 200 Ohms due to the current source Determine the time dependent current i (A) due to the voltage Choose... source Choose... Determine the total effective current (A) flowing through the Choose... inductance with a reactance of 200 Ohms
Solve for 20 V rms supply. Thank you.