(c) A practical voltage regulator involving a Zener diode reference and series pass transistor is shown in Fig. 15. The circuit is connected to an unregulated voltage source VIN VIN (+1 i IN + R 1380 Ω 100 RL VOUT VZ Ζουτ iz Figure 15: Single-transistor voltage regulator. (ii) Sketch the small-signal equivalent circuit of the regulator and simplify your diagram as much as possible.

(c) A practical voltage regulator involving a Zener diode reference and series pass transistor is shown in Fig. 15. The circuit is connected to an unregulated voltage source VIN VIN (+1 i IN + R 1380 Ω 100 RL VOUT VZ Ζουτ iz Figure 15: Single-transistor voltage regulator. (ii) Sketch the small-signal equivalent circuit of the regulator and simplify your diagram as much as possible.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2. Shunt regulator of Figure uses a Zener whose voltage is 5.1V at a current of 10mA, and rz-892. The diode is fed from a supply V=15V (nominal voltage) and R=0.5KQ a) Calculate Vzo. Find Vo with no load and V' at its nominal value. b) Find the change in Vo resulting from a ±1V change in V". c) Find the change in Vo resulting from connecting a load resistance RL that draws a current I1=ImA. d) Find Vo when R₁-0.2KQ. Is the Zener still operating in the breakdown region? mi Zanar ve
2. Draw the waveform of vo(t) of the circuit shown for the given input waveform of vi(t). Label important voltage values. Assume the diode is ideal and the op-am is ideal and saturates at +Vcc and -Vcc. 1K v,(t), volts 10 10 V 1K vo(t) t, sec R 1K -10 V v,(t) (N 2.5 V -10
1500 20V Vin RQ Vout -20V A laptop charger is connected with a load resistance R=44920 and practical PN junction diode is used as shown in Figure. Find the value of the output voltage in the negative half cycle |(in volts) if the input applied voltage is v(t)=20sin314t.
Design a 15 V Zener regulator for the following conditions: 1) The load current IL ranges from 200 mA to 300 mA.2) The source voltage ranges from 21 V to 25 V. Based on your design results,a) Draw the Zener regulator circuit.b) Calculate the power ratings for both Zener diode and resistor Ri
IRL RL In the circuit using a Zener diode above, given that V, = 10 V, R= 3.7 KO, R 6.8 KQ, and the Zener voltage Vz = 5 V. a) The current IRL through the load resistor is b) The current fiowing through the resistor R is:
Draw the waveform of v, of the op-amp circuit shown for the given waveform of vi. Label all important voltage values. Assume the op-amp is ideal and saturates at the positive and negative supply voltages while the diodes are Silicon with forward voltage of 0.7 V. V; (volts) 1K 10 10 V 1K t (msec) 100 2 -10 V -5 4.3 V 4.3 V -10 KH|IH.
G2/0.Desgn Circint as the fallowing peseriptom: A- the positive Cycle of the vout signal is 3.2 and Negatne cycle is 4-3 (Note: we must used preetical Diodes and vin is tov) B- the positive cycles of vout is 5:3 and Negative cycle is (5. 4) [note:consider tovavd we must used Capaetor with praetical Diade) Vin =
None
Consider the following circuit. Assume the on amp is ideal and the diode follows the constant voltage-drop model (ep 0.7 V when forward biased). Dy D2 Calculate t VA, and v.. for the following input voltages. (a). ty +1 V. (b). y= +3 V. (c). ty--1 V. (d). --3 V.
Given the circuit design for a Zener diode regulator in the previous question, what is the maximum power that will be dissipated by the Rs resistor? You are told that the source voltage Vs varies from 6 V to 13 V, the load current il varies between 2 mA and 47 mA, and the diode is an ideal 4 V Zener diode. You will need to recalculate the maximum allowable resistance Rs with your new values, as part of this question. Please enter your answer to 3 significant figures, and in Watts.
Please label all important voltage values. Thank you.
Q2 In the circuit as shown below. Determine the (ripple factor) and sketch vp(out) for the filtered bridge rectifier with a load as indicated. 2 : 1 D3 D1 120Vp-p f= 50HZ + Output V1 V2 D2 D4 1uf R1=2k