electronic ·Elektronik Mühendisliği (%30 İng.) (II) / E2M341 Elektronik / Genel / Kisa sŞekildeki devre için Ago kabul ederek, aşağıdakileri hesaplayınız.1. Kutup frekansının 1,5 MHz'e yerleşmesi için gerekli C, değeri nedir?2. Sistemin sifir frekansını kutup frekansının yirmide biri frekansa yerleştirmek için gerekli R₂ değeri nedir?For the opamp circuit shown below figure, calculate the followings by assuming A0=00,1. What is the required value of C, to locate the pole frequency at 1,5 MHz?2. What is the required value of R₂ to place the zero frequency of the system at the frequency of one-twentieth of the pole frequency?Circuit parameters/Devre ParametreleriR₁ =3,1 kQceki sayfaR₂Wo VoutC₁ R₁AO a. C1=61,6 pF, R2=40,3kO b. C1=34,2 PF, R2=58,9kQO c.C1=41,1 pF, R2=58,9kOd. C1=41,1 PF, R2=40,3kO e. C1-47,9 pF, R2=71,3kOf C1-47,9 pF, R2=49,6kOg. C1-54,8 pF, R2=71,3kO h. C1-34,2 pF, R2=49,6k<- DuyurularESCaGeçiş yap...@2F3##*NF4F540$%L?F6myhpA-97+4&

Answered: Image /qna-images/answer/4170be20-9dff-401a-bc60-79bbdb769fae.jpg

Answered: ·Elektronik Mühendisliği (%30 İng.)…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

6 volts are applied through a 2 cm long semiconductor rod. Average drift velocity is 104 cm/s. What is electron mobility?
question 2
These question from electronics two course
Design a synchronous counter using JK flip-flops to produce the following sequences. 2 4 6. 3 1
2.3 A thermocouple element when taken from a liquid at 50°C and plunged into a liquid at 100°C at time t-0 gave the following e.m.f. values. Determine the 95% response time. Time (s) e.m.f. (mV) 2.5 20 40 60 80 100 120 3.8 4.5 4.8 4.9 5.0 5.0
X=5 y =4 YX=54
Q1. Determine the class of mater ial based on relative comparison for each energy diagram. Energy Energy Energy Conduction bund Energs gap Conduction band Energy gap Conduction band Overlap Valence band Valence bund Valence band (b) Assignment1- (ENEL2104) Page 1 Q2. What are the major carriers in the depletion region? Explain.
1.17 Test data from four components are given below. Each test consists of a complete traversal from an input value of 0 to an input value of 25. The data are listed in the order in which the traversal was made. Plot the data from each test on an input/output graph with the input on the horizontal axis and the output on the vertical axis. Use ar- rows to show the direction of traversal. 1.18 Identify all nonlinearities exhibited by each compo- nent in Exercise 1.17. Component 1 Input 0 5 10 15 20 25 20 15 10 50 Output 0 16 38 62 84 100 84 62 38 16 0 Component 2 Input 0 5 10 15 20 25 20 15 10 50 Output 0 18 36 56 78 100 82 64 44 22 0 Component 3 Input 0 6 10 15 20 22 25 19 15 10 5 30 Output 10 10 30 55 80 90 90 90 70 45 20 10 10 Component 4 Input 0 6 10 15 20 22 25 19 15 10 5 3 0 Output 10 10 27 50 78 90 90 90 73 50 22 10 10
What is CEMF?
Identify each characteristic curve by the type of FET that it represents. Ip +VGs -VGS
Refer to this Figure 1. Determine the minimum value of IBthat will produce saturation.
Ims.cisjubail.gov.sa/webapps/assessment/take/launch.jsp?course_assessment_id%3 34730_1&course_id%3_56188 18content id%3 1713242 1 Ta Remaining Time: 46 minutes, 48 seconds. Question Completion Status: -30V- QUESTION 6 Determine whether each silicon diode in the following figure is forward biased (fb) or reversed biased (rb) Using the practical model, the voltage across the diode is V. 10 N 5V 5V Click Save and Submit to save and submit. Click Save All Answers to save all answers.

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS