Both portions of the rod ABC are made of an aluminum for which E = 70 GPa.0.4 m0.5 mBP20-mm diameter60-mm diameter2. What is the value of Q in kN so that the deflection at A is zero if P = 59 kN?

Objective: To determine the value of load Q, such that the deflection at A is zero. Given: P = 59…

Answered: Both portions of the rod ABC are made…

Both portions of the rod ABC are made of an aluminum for which E = 70 GPa. 0.4 m 0.5 m B C 20-mm diameter 60-mm diameter

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

At a temperature of 60°F, a 0.04-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; α=α=12.5 x 10-6/°F] bar with a width of 2.5 in. and a thickness of 0.75 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; α=α=9.6 x 10-6/°F] bar with a width of 1.7 in. and a thickness of 0.75 in. The supports at A and C are rigid. Assume h1=2.5 in., h2=1.7 in., L1=31 in., L2=46 in., and Δ=Δ= 0.04 in. (A) Determine the lowest temperature, Tcontact, at which the two bars contact each other. (B) Find a geometry-of-deformation relationship for the case in which the gap is closed. Express this relationship by entering the sum δ1+δ2, where δ1 is the axial deflection of Bar (1), and δ2 is the axial deflection of Bar (2). δ1+δ2= _____in. (C) Find the force in the Bar (1), F1, and the force in Bar (2), F2, at a temperature of 225oF. By convention, a tension force is positive and a compression force is negative. IN KIPS (D) Find σ1 and σ2,…
The pin-connected structure shown consists of a rigid bar ABCD and two axial members. Bar (1) is steel [E = 200 GPa; a = 11.7x 10-6/°C], with a cross-sectional area of A1 = 370 mm2. Bar (2) is an aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C], with a cross- sectional area of A2 = 380 mm?. The bars are unstressed when the structure is assembled. Assume a=360O mm, b=620 mm, c=730 mm, P=20 kN, and L=890 mm. After a concentrated load of P = 20 kN is applied and the temperature is increased by 35°C, determine (a) the normal stresses in bars (1) and (2). (b) the deflection of point D on the rigid bar. A (1) B (2)
A rigid bar, AB, is pinned at point B. Two other bars, AC and AD, are connected to point A to provide support for AB. We are investigating the behavior of this system under a specific load. Key Details: Bar properties: Material: Steel with Young's modulus (Esteel) of 200 GPa and coefficient of thermal expansion (a) of 11.7 x 10^-6 /°C. Cross-sectional area: AC: 1960 mm² AD: 1250 mm² Length: AC: √2 meters (square root of 2 meters) AD: 1 meter Inclination angles: AC: θ₁ (theta 1) = 30° from horizontal AD: θ₂ (theta 2) = 20° from horizontal Load on bar AB: Idealized linearly increasing load with a maximum value of 30 kN/m at point B. Problem Objectives: Determine the internal forces (axial forces) acting within bars AC and AD due to the applied load on AB. Calculate the displacement of point A in both horizontal (dA,x) and vertical (dA,y) directions.If the bar is cooled by 10°C, what would be the: Determine the internal forces (axial forces) acting within bars AC and AD…
simple strain with fbd
At a temperature of 29.8 °C a 0.4-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 133.3°C, determine the change in length of the steel rod if L = 312.45 mm and M=201 mm. Round off the final answer to four decimal places. d - L M - B Aluminum A = 2000 mm² E = 75 GPa a = 23 x 10-6/°C Stainless steel A = 800 mm² E = 190 GPa α = 17.3 x 10-6/°C
The axial assembly consists of a solid 1.13-in-diameter aluminum alloy [E = 8300 ksi, v = 0.27,a = 11.1 x 10-6/°F] rod (1) and a solid 1.59-in-diameter bronze [E = 15100 ksi, v = 0.16, a = 8.7x 10-6/°F] rod (2). Assume L1=17 in., L2=27 in. If the supports at A and C are rigid and the assembly is stress free at 14°F, determine: (a) the normal stresses o1,02 in both rods at 176°F (positive if tensile, negative if compressive). (b) the displacernent ug of flange B (positive if to the right, negative to the left). (c) the change in diameter Ad, of the aluminum rod. B (1) (2) L1 L2 Answers: (a) oj = i 23.253 ksi, o2 = i 11.745 ksi (b) ug = -0.017055 in. (c) Adj = in. 0.0020319
Structural members that are rectangular, square, or round tubular members frequently utilized as columns, hangers, and braced-frame members. a.) HOLLOW STRUCTURAL SECTIONS b.) S-SHAPES c.) WT-SHAPES d.) HP-SHAPES
Please answer in detailed solution and explain step by step
It is a structural system that is often used in buildings and mainly composed of beams and columns that are either pin or fix connected. The strength of this system is derived from beam-column interaction at rigid joints. a. Statically determinate structures b. Shear structure c. Truss system d. Frames
A mild steel flat of width 120 mm and thickness 10 mm is bent into an arc of a circle of radius 10 m by applying a pure moment 'M'. If E is 200 GPa, then magnitude of the pure moment 'M' will be
Knowing that a 0.02in gap exists when the temperature is 75°F, determine (a) the temperature at which the normal stress in the aluminum bar will be equal to -11ksi, (b) the corresponding exact length (2 decimal places in 103 inches) of the aluminum bar. 0.02 in. 14 in. Bronze A = 2.4 in² E = 15 × 106 psi a = 12 x 10-6/°F 18 in. Aluminum A = 2.8 in² E = 10.6 × 106 psi a = 12.9 x 10-6/°F
Choose correct option. ___________ refers to a configurational property that preserves the geometry of the structure through its elements strategically arranged and interacting together to resist loads. a. Spatial support b. Structural balance c. Symmetrical equilibrium d. Geometric stability