BD bar is 50mm wide and 15mm thick. All pins are 12 mm in diameter and have a one-sided cutting effect.   A) Find the greatest normal stress on the bar BD. B) Find the shear stress occurring at the D pin. C) Find the bearing stress at point D of the bar BD.

Q: what is the value of maximum principal stress in the figure below?

A: Find the maximum principal stress .

Q: Problem 4 only, solve carefully, include the units in every step and draw the diagram. Thanks! A…

A:

Q: Question 1: 1. The figure shows two steel shafts connected by a steel pipe with interference.…

A: Turning operation is the manufacturing technique that is done on a lathe machine. In this operation,…

Q: Question 3) Plane stress state at a point is given in the figure. a) Calculate the principal…

A: τxy=10 Mpaσ1,2=σx+σy2±σx-σy22+τxy2 As it is case of pure shear so σx=0 and σy=0…

Q: For the state of plane stress shown in Figure-1. below; a) Draw Mohr's circle, b) Find the maximum…

A: Given Data: The stress in the x-direction is, σx=-20 MPa. The stress in the y-direction is, σy=90…

Q: 1) A 35 mm diameter shaft operating at 2000 rpm transmits 1000 kW. The bending and axial loads on…

A:

Q: Please answer in this format. Sketch: Given: Required: Solution: (Please answer in detailed (step by…

A:

Q: 20 mm- 50 mm 20 mm 100 mm 50 mm 100 mm M-8 kN-m A unique strut, shown in the figure, will be used in…

A:

Q: Question 3 Based on the diagram below a) Find the internal forces of A, B & C. 950 тm 045 тm Ø30mm F…

A: First we need to calculate the reaction from the wall by balancing all the forces.  Sum of all the…

Q: Find the required diameter d0 for a solid circle shaft. b) Find the required outer diameter d2 for a…

A: Given: T =1200 NM G=78 GPa Allowable shear stress =40 MPa Allowable rate of twist 0.78/m TO…

Q: Figure 1 shows a T-beam section contains a flange of size 120 mm by 10 mm and web of size 20 mm by…

A: The area moment of inertia, also known as the second area moment or 2nd moment of area, is a feature…

Q: S-1) Given in Figure 1; a) Find the dimensions d, b and c? b) Calculate the stresses occurring in…

A: Stress : When an object is applied an external force or moment a resistance force is setup within…

Q: Q.1. A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138,…

A:

Q: In an industrial machine, two shafts have to be connected by using a muff coupling. The shaft…

A: Given,

Q: The specification of a cylindrical vessel are as follows: D = 350 mm t = 12 mm P = 4.5 MPa Determine…

A:

Q: If you have a rod with an initial diameter 12 mm, final diameter is 10 mm and yield stress 40Mpa, it…

A:

Q: A machine part is subjected to an axial loading situation where Fmin = 3700 lbf and Fmax = 12000…

A: Given:Maximum axial force, Fmax=12000 lbfMinimum axial force, Fmin=3700 lbfCross-sectional area,…

Q: The built-up shaft consists of a pipe AB and solid rod BC. The pipe has an inner diameter of 18 mm…

A: Part A) The outer diameter of the tube is do = 24 mm = 0.024 mThe inner diameter of the tube is di =…

Q: cylindrical pressure vessel has inside diameter d_{o} = 500 mm and inside diameter di=490 mm.if it i…

A: Given Data Outside diameter of vessel is: do=500 mm Inside diameter iof vessel is:di=490 mm Factor…

Q: why do you multiply by 16 in the shear stress?

A: This question is based on the concept of Torsion equation.

Q: choose the correct answer Mcq: the maximum shar stress in contact between two steel spheres pressed…

A: Option one is correct. At the contact surface

Q: Please don't provide handwritten solution...

A: First, we need to calculate the torque TBC. The torque TBC can be calculated by subtracting the…

Q: For each of the structures shown in Fig.2, sketch the following: i. Free body diagrams showing the…

A: Given: FA = 300 lbf FB = 750 lbf

Q: 3) -3 m For thin walled pressure vessel: Inner radius =50 em Wall thickness -3 cm P-P'= 0 kN Gage…

A:

Q: uired to mount a pulley on the sh

A: Given data Dia of shaft =80 mm Maximum shear stress = 63 MPa

Q: 3. A vertical load of 500 N acts at the end of a rectangular cantilever beam 2 m long and 25 mm…

A: Given : load P = 500 Nlength of beam L = 2 m = 2000mmwidth of beam b = 25 mmBending stress  = 130…

Q: Hertz contact theory can be used to determine the stresses due to contact between two spheres, which…

A: It is asked to find the stress by using Hertz contact theory

Q: The force P = 4 kN is applied to the steel (E = 200 GPa) rod AB of diameter d 50 mm. a) Determine…

A:

Q: Calculate each of the following under 20 kN load on a structure given below where all pins have a…

A: Given details: P=20 kNd=10 mmζy=300 MPan=2

Q: The 100 mm diameter steel bar is bored to 50 mm diameter over half its length as shown in Figure Q2.…

A: The diameter of steel bar, D = 100 mm  = 0.1 mThe internal diameter, d = 50 mm = 0.05 mThe shear…

Q: Q4/ Answer one A) A cylindrical rod of 16 mm diameter is made of plain carbon steel. It is subjected…

A:

Q: connected by using a muff coupling. The shaft rotates at a speed of 620 rpm and transmits a power of…

A:

Q: Problem 8. A 6 kN load is applied at point A. Points B,C, and D are pin joints. The structure is…

A:

Q: d.Tensile stress in the cable in MPa. e.Shearing stress at B in MPa.

A:

Q: method is used to find stresses on an oblique plane of a member when it is subjected to stresses in…

A: OPTION (B) Mohr's circle

Q: 2. COMPUTE THE: A. PROPORTIONAL LIMIT B. MODULUS OF ELASTICIT Y C. YIELD STRESS AT 0.2 % OFFSET D.…

A: Given: The diameter of specimen, d = 12.5 mm The gauge length, L = 50 mm

Q: Calculate each of the following under 20 kN load on a structure given below where all pins have a…

A:

Q: Construct a Mohr circle using below information and label it appropriately. Using Iohr circle, find…

A: givennormal stress in X direction σX=150Mpanormal stress in Y diretion σY=100Mpasheer stress at XY…