Solve the following problems and SHOW YOUR COMPLETE SOLUTIONS FOR BETTER UNDERSTANDING Solve the following problem and show your complete solutions.3. A vertical load of 500 N acts at the end of a rectangular cantilever beam 2 m long and 25 mm wide.If allowable bending stress is 130 MPa, find the depth of the beam

Given : load P = 500 Nlength of beam L = 2 m = 2000mmwidth of beam b = 25 mmBending stress = 130…

Answered: 3. A vertical load of 500 N acts at the…

3. A vertical load of 500 N acts at the end of a rectangular cantilever beam 2 m long and 25 mm wide. If allowable bending stress is 130 MPa, find the depth of the beam

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.5.8P: A freight-car axle AS is loaded approximately as shown in the figure, with the forces P representing...

See similar textbooks

Related questions

Q: uniform supersonic flow of a perfect gas with y = 1.4, a Mach number of 3.0, and an up- eam static…

Q: 37. What factor of safety is needed for a 1.998 in diameter shaft with an ultimate * strength of…

Q: A horizontal tube of 125 mm diameter with an outer surface temperature of 240°C is located in a…

Q: 4. The angle of twist of a 2.0 m long transmission shaft must not exceed 2 degrees when a torque of…

Q: 40. What load in N must be applied to a 25 mm round steel bar 2.5 m long (E = 207 Gpa) to stretch…

Q: A mass is leaning against a spring, compressed of a distance d = 50 cm. Compute the speed of the…

A: Given:To find:Speed of massDistance traveled

Q: Determine the moments of inertia of area with respect to centroidal axis parallel to y-axis as shown…

Q: How are composites classified based on the matrix material? Give one example of each type.

A: Classified of composite based on matrix material

Q: 6.7 A converging-diverging nozzle is designed to provide flow at Mach 2.0. With the nozzle…

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 3550 mm² and an…

A: Given data :- Area A1 = 3550 mm2 ; Allowable normal stress =175 MPaArea A2 = 2050 mm2 ;…

Q: 22. A man borrowed P300,000 from a bank and agreed to pay the loan at the end of the months. The…

Q: Exercise We consider an ideal Diesel Cycle whose compression ratio Amax - 18. The heat transfer er…

A: The compression ratio of diesel cycle is The heat addition to the cycle is The initial temperature…

Q: 31.6What load in N must be applied to a 25 mm round steel bar 2.5 m long (E = 207 Gpa) to stretch…

Q: Boom OAB is supported by a ball and socket at point O and two cables AC and AD. Determine the forces…

Q: 7.4 A reservoir containing air at 2 MPa is connected to ambient air (y = 1.4) at 101 kPa through a…

A: The Prandtl number (Pr) or Prandtl bunch is a dimensionless number, named after the German physicist…

Q: 16. Steam at 2 Mpa and 250°C in a rigid cylinder is cooled until the quality is 50%. * Find the heat…

A: Given data,At 2mPa and 250∘C,Quality, x= 50%V=0.11144m3/kgu=2679.6KJ/kgAt 2mPa (saturated),Vf=…

Q: FINAL ACTIVITY 1. A tension test was performed on a steel specimen having an original diameter of…

A: Given: The diameter of the bar, N = 0.03n The length of the bar, L = 4N

Q: 19. Find the loss of head in the pipe entrance if speed of flow is 10 m/s. OA. 5.10 m OB. 10.2 m O…

Q: Solve the following problems and show your complete solutions for better understanding. Explain your…

A: Given:The radius of the fixed circular path is The limits of Between the given limits, the angular…

Q: A heat exchanger is built as a bundle of 120 small steel tubes (outer diameter: 1 cm, inner d 0.9…

A: GIVEN: numbers of tube: n=120 outer diameter of tube: do=0.01m inner diameter of tube: di=0.009m…

Q: solve the following problems and show your complete solutions for better understanding. Expla your…

A: To calculate the acceleration of the particle.Given the impeller speed speed of the fluid particles…

Q: Design a timber glue-lam beam made from douglas fir for the given load in the figure below. 3. 670…

A: Here exactly what is required is not specifically mention So we are doing it in the following way…

Q: Steam flows at 60 m/s through a steam main of 1.6 MPa, 280°C. Four tanks are connected to this main…

Q: Please solve the following question for practice, I just want to check my answer and make sure I…

A: The objective of the question is to determine the mass of the iron. This can be achieved by applying…

Q: Exercise 2 Triangular Cycle. ble consider the reversible cycle below described by an Ideal gas. Xx…

Q: 2. A cell has a terminal voltage of 50.0 V for a current of 10.0 A, and 54 V for a current of 6.0 A.…

A: let R = internal resistance, V open circuit voltage. 50 = V – 10*R 54 = V – 6*R subtract the two 4…

Q: 2kN/m 2.5m B * 2m C 2kN/m 2.5m * ⒸV @ 2.7m from A ⒸMC 4.6m from A Ⓒ Ely' @ 4.5m from A

Q: The particle P starts from rest at point A at time t = 0 and changes its speed thereafter at a…

Q: 4. A quantity of water is admitted from a water main into an evacuated 60 L adiabatic vessel (see…

A: Given:The capacity of the water vessel is .The pressure of the water is .The temperature of the…

Q: Solve the following problem and show your complete solutions. 4. A solid cylindrical shaft 48.2 cm…

Q: A copper-silver alloy of composition 30 wt% Ag-70 wr% Cu is at 7800C (Just above the eutectic…

A: To Find : a) The phases present.b) The mass fractions of each phase given in part (a) -Liquidus…

Q: Ruestion 3 The combined pulleys in Figure 3 use friction to transmit motion. If block A has a linear…

Q: Steam flows through a bank of nozzles shown in the figure, with wall thickness t2=2 mm, spacing s=4…

Question

Solve the following problems and SHOW YOUR COMPLETE SOLUTIONS FOR BETTER UNDERSTANDING

Solve the following problem and show your complete solutions.
3. A vertical load of 500 N acts at the end of a rectangular cantilever beam 2 m long and 25 mm wide.
If allowable bending stress is 130 MPa, find the depth of the beam

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: given_data

VIEW

Step 2: Figure

VIEW

Step 3: calculation-1

VIEW

Step 4: calculation-2

VIEW

Step 5: calculation-3

VIEW

Solution

VIEW

Step by step

Solved in 6 steps with 19 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

-15 A composite beam is constructed froma wood beam (3 in. x 6 in.) and a steel plate (3 in, wide). The wood and the steel are securely fastened to act as a single beam. The beam is subjected to a positive bending moment M. = 75 kip-in. Calculate the required thickness of the steel plate based on the following limit states: Allowable compressive stress in the wood = 2 ksi Allowable tensile stress in the wood = 2 ksi Allowable tensile stress in the steel plate = 16 ksi Assume that Ew= 1,500 ksi and es= 30,000 ksi.
The Z-section of Example D-7 is subjected to M = 5 kN · m, as shown. Determine the orientation of the neutral axis and calculate the maximum tensile stress c1and maximum compressive stress ocin the beam. Use the following numerical data: height; = 200 mm, width ft = 90 mm, constant thickness a = 15 mm, and B = 19.2e. Use = 32.6 × 106 mm4 and I2= 2.4 × 10e mm4 from Example D-7
At a full d raw, an archer applies a pull of 130 N to the bowstring of the bow shown in the figure. Determine the bending moment at the midpoint of the bow.
A wood beam reinforced by an aluminum channel section is shown in the figure. The beam has a cross section of dimensions 150 mm x 250 mm, and the channel has a uniform thickness of 6.5 mm. If the allowable stresses in the wood and aluminum are 8 M Pa and 38 M Pa, respectively, and if their moduli of elasticity are in the ratio 1 to 6, what is the maximum allowable bending moment for the beam?
A beam having a cross section in the form of a channel (sec figure) is subjected to a bending moment acting about the z axis. Calculate the thickness t of the channel in order that the bending stresses at the top and bottom of the beam will be in the ratio 7:3, respectively.
A freight-car axle AS is loaded approximately as shown in the figure, with the forces P representing the car loads (transmitted to the axle through the axle boxes) and the forces R representing the rail loads (transmitted to the axle through the wheels). The diameter of the axle is d = 82 mm, the distance between centers of the rails is Z., and the distance between the forces P and R is A = 220 mm. Calculate the maximum bending stress vmaxin the axle if P = 50 kN.
The bending moment M is applied to the box beam in the x-y plane at the orientation show below. (a) Determine the maximum magnitude of the bending moment M so that the tensile bending stress in the member does not exceed 15 ksi. (b) Determine the angle that the neutral axis makes with the y-axis. (c) The position or positions on the beam where the maximum compressive bending stress occurs given your answer in a. Clearly indicate this on the figure below (also calculate the values) 4 in. B 4 in. M 6 in. 6 in.
a 80 mm wide and 300 mm high simply supported bean has a length of 7.4 m and supports a concentrated load of 7.2 kN acting at the midspan. Find the maximum shear stress and maximum bending stress.
Solve the following problem with complete solutions and fbd
The simply supported beam of circular cross section carries a uniformly distributed load of intensity wo over two-thirds of its length. What is the maximum allowable value of wo in kN/m if the working stress in bending is 50 MPa? Wo 50 mm 1.0 m 2 m
Your answer is partially correct. For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=2.50 m, b=4.25 m, Pg= 45kN, and Pc = 90kN. Construct the shear- force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. Answers: Ay= a 74.189 B Calculate the reaction forces Ay and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Dy= i 59.21 B a PB a Pc KN Pc b KN D b D P x
A circular solid cross-section cantilever is fixed at one end and bears a concentrated load P at the other. Over a 2m length, the diameter increases uniformly from 200 mm at the free end to 400 mm at the fixed end. At what distance from the free end will the bending stress in the cantilever be maximum? If the concentrated load P=30 KN, what is the maximum bending stress