B3 N : S0 Ny=25 N4= 30 3. 150 r/min S+ = 9N 2 Output Input W6=? N Arm

Q: In the crank-slider shown, OA = 5 cm, AB = 15 cm and the offset e = 7 cm. Find the value of angle a…

A:

Q: Fill in the blank which is given below Linear acceleration is equal to the product of and angular…

A:

Q: A compressor motor has a shaft diameter of 7⁄8 inch. The felt wiper that wrapstightly around the…

A: Given    Diameter,d = 7⁄8 inch.

Q: The pictured disk which weighs 20 lbs. and contacts an inclined surface (this inclined surface is…

A:

Q: thread the outer Jiem 10

A: Given data Outer diameter =26mm Inner diameter =18mm

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: Determine the thickness (mm) of a spur gear tooth with a diametral pitch of 7.01, measured along the…

A:

Q: If the ratio of the velocity of outward stroke and velocity of return stroke is 8, then the Koitie…

A:

Q: 04/ Determine suitable groove dimensions for a 0101-16 '0' ring to seal against a solid cylinder.

A: Given that ,  Determine suitable groove dimension for a 0101-16 'O' ring to steal against a solid…

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: Write a CNC program code to machine this part.

A: Since the part is symmetrical, thus divide the given component into half and the half part.

Q: find the requird fillet Size Ch) for figew soンル2 ん。 レン46cm 26cm /2

A: Given data: -  The shear stress for all joints is τ = 0.5 MPa. The length L is L = 40 cm. The…

Q: R.75 00.63 THRU $5 01.123 0.250 E 1.38 0.63 mm radius hole partially through the part 0.63 mm radius…

A:

Q: If the taper angle, large diameter, smaller diameters are respectively 2°, 44 mm, and 34mm. Find the…

A:

Q: Redraw when the rack AB is at 45o angle. What are the other two angles belonging to the triangle…

A:

Q: 4. What is the complement of a 72°21'47" angle?

A: We know that the complement angles pair have sum = 90o let x =  72o 21' 47"  (Given) Complement of x…

Q: 4. Determine the length of stroke of a slider E when the crank AC rotates by 30 degrees in counter-…

A: Find the attachment for the solution.

Q: Through load analysis, force and moment diagram are obtained, as shown below. Diagram below shows…

A: The force that occurs between mating gears is normal to the surfaces in contact. The axial force Fa,…

Q: . Graphically position the links for the embossing mechanism in the config- shown below. Then…

A: Link  ABG is one link.

Q: 1. If the block is loaded with P = 282 kN, calculate the required dimension "b" of the key.   Write…

A:

Q: For the laser cutting of the shown path, determine the absolute and incremental coordinates of the…

A: Given Laser Cutting To find Coordinate for absolute and incremental

Q: Determine the horizontal and vertical stroke of a slider D and F when crank AB rotates 30 legrees…

A:

Q: solve the following exercises:

A: To determine the acceleration of the system

Q: Draw the following spring with all mensions in sheet (write down all the equations you used in the

A:

Q: Redraw when the rack AB is at 89o angle. What are the other two angles belonging to the triangle…

A: When the rack AB is at 89o angle. Draw the diagram as given above.

Q: Q/Find the value of T (kN. m/m) So that the value of angle of twist at D equal to zero.

A: The elemental angle of twist for the shaft CD can be expressed as, On integrating the above…

Q: :Find dimension y all dimensions are in inches 0.664 R 58°50' 2.800 R 1.120 0.400 R

A:

Q: .a. 12 b.. 3. C. 12 12.(2.6+1.5)-1.1? a.4.1 Perform as indicated: Write the letter of your choice on…

A: Hi and thanks for the questions. Since you have asked multiple questions, we will solve the first…

Q: Express the quantity 254,998m in mm.

A: To convert meter quantity into millimeter one must be familiar with the no. of mm exist in one…

Q: o shafts 3679mm between centers carry pulleys 1288 mm in diameter and 910 mm in  diameter…

A: dL= diameter of larger pulley dS= diameter of smaller pulley C= distance between the centers of…

Q: f e (D d b C a k j a=38.0 b=41.5 c=39.3 d=40.1 e=55.8 f=39.4 q=36.7

A: a = 38.0b = 41.5c = 39.3d = 40.1e = 55.8f = 39.4g = 36.7h = 65.7i = 49.0j = 50.0k = 61.9l = 7.8m =…

Q: If the taper angle, large diameter, smaller diameters are respectively 2°, 44 mm, and 34mm. Find the…

A:

Q: For the following internal dovetail, if bis 40mm greater than c, m is 60mm less than b, h is 25 mm…

A:

Q: Draw a common tangent to two circles of diameter 6cm and 4cm respectively if the distance between…

A:

Thermodynamic Relations

Thermodynamics is the division of physics that deals with the transfer of any kind of energy, whether it be heat, temperature, or work, from one object to another.