B/ Water in a rigid, insulating tank is set in rotation and left. Water comes to rest after some time due to viscous forces. Considering the tank and water to constitute the system answer yes or no. (i) Is any work done during the process of water coming to rest? (ii) Is there a flow of heat? (iii) Is there any change in internal energy (U)? (iv) Is there any change in total energy (E)?

B/ Water in a rigid, insulating tank is set in rotation and left. Water comes to rest after some time due to viscous forces. Considering the tank and water to constitute the system answer yes or no. (i) Is any work done during the process of water coming to rest? (ii) Is there a flow of heat? (iii) Is there any change in internal energy (U)? (iv) Is there any change in total energy (E)?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In this discussion, you will briefly explain each of the four gas laws and apply an example as it happens in a refrigeration system. (Boyle’s, Charles’, Dalton’s, and the general law of perfect gases). In your contribution, also address the following: What makes matter change to different states? What type of energy do you think is the most important for the HVAC-R industry?
Q2/ Determine whether the state of the following water system is compressed liquid, mixture of saturated liquid and saturated vapor, or superheated vapor. (a) T=100°C, P=3.0MPA (b) T=300°C, P=100kPa (c)T=100°C, v=1.6m'/kg (d) P=0.2MPA, u=700KJ/kg
Help me please
A torque of 2 N-m is necessary to rotate a paddle wheel at a rate of 20 rad/s.The paddle wheel is located in a rigid vessel containing a gas. What is the net work injoule done on the gas during 10 minutes of operation?
Water contained in a piston-cylinder assembly undergoes two processes in series (point 1 to point 2 and point 2 to point 3): point 1: T1 = 100°C and P1 = 5bar point 2: 71= 151.9°C and P2 = 5bar and v2 = 0.300 .300 m³ point 3: 73= 200°C and v3 = .300" kg Use the thermodynamic tables A.2, A.3, and A.4 to answer the following questions: For questions 1, 3, and 5 choose from: subcooled water, saturated water, saturated liquid, saturated vapor, superheated vapor 1) What is the thermodynamic state of water at point 1: 2- What is the specific volume of water at point 1: 3) What is the thermodynamic state of water at point 2: 4) What is the quality of water (x) at point 2: 3) What is the thermodynamic state of water at point 3: 4) What is the pressure of water at point 3: (bar) On paper draw points 1, 2, and 3 on the following P-v and T-v diagrams and show the two processes. Add number values, units, and constant pressure or temperature lines if needed. Specify which table you used to find…
The 1st law of thermodynamics is ΔU = Q –W. Use this statement of the 1st law to show (mathematically) its equivalent statement: “Total energy of the universe is constant”. Here, the universe can be defined as: system + surroundings (everything but the system –everything outside the system). (Hint: this can be shown by two ways-you may either treat system and surroundings as two systems next to each other, or you may treat system + surroundings (universe) as one system.)
Fill in the blanks: Magnolia Dairy product must cool 4000 gallons of fresh milk from the farm from an initial temperature of 80°F to a temperature of 38°F in 5 hours. If the density of the milk is 8.6 lb/gal, sg 1.03 and Cp = 0.935 BTU/lb-R, how much brine must be circulated in gpm, if the change in temperature of brine is 15F°, sg = 1.182 and Cp = 0.729 BTU/lb-R? %3D gpm
Mechanical Engineering A steam turbine receives hot & pressurized steam from the inlet (port 1 in the figure), produces work, and discharges steam at low pressure and temperature to the outlet (port 2). P1 = 1.5 x (modifier) MPa, T1 = 350 x (modifier) °C. P2 and T2 are given in the figure. The turbine is at a steady state. Kinetic energy and gravitational potential energy of the steam are negligible compared to its thermal energy. q is negligible Turbine w? P1= T = im =16 kg/s 2+ P, = 0.2 Mpa | T, = 150°C (a) Mass flow rate at the inlet is 10 kg/s. Compute the mass flow rate at the outlet. Show your reasoning (b) Determine the change of specific enthalpy of the steam between the inlet and the outlet. You can assume the specific heat of steam remains essentially constant during the process, with C, = 1.9 kJ/kg.K (c) Compute the work produced by the steam turbine, per unit mass of steam. (d) Compute the power production from the turbine. Power is the work produced per time, and its most…
A body of mass 20 kg falls freely in vacuum. It has fallen through a vertical distance of 50 m. The gravitational acceleration may be assumed as 10 m/s?. What is the thermodynamic work done by the body?
In an engineering system, air passes through two sequential processes. These processes Information about it is given below. Process 1-2: Polytropic compression, n = 1.3, P1=100 kPa, v1 =0.04 m3 /kg v2 =0.02 m3 /kg. Process 2–3: v3 = constant pressure process up to v1. In the light of this information, 1)draw the P-v diagram of the system. 2)Work per unit air mass in kJ/kg set as.
0.56 kg of water in a piston cylinder device as shown initially the water is at T, = 120 °C with volume V, = 36 L (State 1). Heat is then added such that all the water in the cylinder is saturated vapor and the piston just touched the spring without exerted any force on the spring (State 2). Then additional heat is added to the system such that the temperature is T, 600 °C and the pressure is P,= 400 kPa (State 3). 3 Po 3 1) Find the total work (from state 1 to state 3, in kW). O 147.73 2) O Not listed Qin 111.16 133.48 107 23 156.11 125.24 2) Find the total heat transfer for the process (from state 1 to state 3, in kW). 1424.6 O Not listed O 1486.0 O 1585.4
20. Two objects are connected to each other by a rope over a pulley as in the figure. The 8.00 kg and mp = 11.0 kg. If initially ma is at rest 1.36 m from the masses are mA= edge of the table, how long does it take to reach the edge of the table if the system is allowed to move freely (i.e. with no friction)? Mg (c) 1.97 s (a) 12.3 s (d) 0.692 s (b) 0.413 s (e) 5.38 s