Magnolia Dairy product must cool 4000 gallons of fresh milk from the farm from an initial temperature of 80°F to a temperature of 38°F in 5 hours. If the density of the milk is 8.6 lb/gal, sg = 1.03 and Cp 0.935 BTU/lb-R, how much brine must be circulated in gpm, if the change in temperature of brine is 15F°, sg = 1.182 and Cp = 0.729 BTU/lb-R?

Magnolia Dairy product must cool 4000 gallons of fresh milk from the farm from an initial temperature of 80°F to a temperature of 38°F in 5 hours. If the density of the milk is 8.6 lb/gal, sg = 1.03 and Cp 0.935 BTU/lb-R, how much brine must be circulated in gpm, if the change in temperature of brine is 15F°, sg = 1.182 and Cp = 0.729 BTU/lb-R?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Methanol (SG=0.792) is contained in a large tank under a pressure of 350000 Pa absolute. When a valve on the bottom of the tank is opened, the methanol drains freely though a 0.02 m ID tube whose outlet is 7.00 m below the surface of the methanol. The pressure at the outlet of the discharge pipe is 101325 Pa. Some useful constants and conversions: g = 9.8 m/s2 , Pref = 1000 kg/m3 . a. Draw the system. Label points I and 2 (where you will define A= 2-1) and label the variables with values b Write the general form of the energy balance. Cancel out negligible terms, and state the keyword/assumption to justify. Simplify to the resultant energy balance. c.) Assume the diameter of the tank is very big compared to the drain tube velocity, which make the velocity of liquid in the tank equal to zero. Estimate the methanol discharge velocity in the drain tube in m/s. *hint: divide your EB by m to eliminate m and V. Recall, n = pV = pvA and = v/m=1/p
Air is contained in a piston cylinder arrangement as shown in Fig.(Refer attachment). The piston can be assumed to be massless, frictionless, and perfectly insulated. 10 kg of dry ice (solid CO2) is placed on top of the piston. The initial conditions for air inside the cylinder are P1=121 kPa, T1= 300 K. Dry ice sublimates gradually, and its mass reduces to 5 kg. Ambient air is always at room temperature (27oC) and atmospheric pressure. (Given: R=287 J/kg ·K, g = 9.8 m/s2, CP/CV for air = 1.4; Neglect all heat transfer to the dry ice block.) a)Assuming the cylinder to be perfectly insulated, calculate the specific work done for the process. b)Assuming the cylinder to be perfectly conducting, what is the heat required per unit mass of air to complete the process? c) Plot the processes described in (a) and (b) together on a P-V diagram. From this plot, which process appears to have more work? Explain.
Exhaust gas leaves the exhaust pipe of a motor car with a pressure of 1.2bar and a temperature of 400 degree C. If the exhaust gas specific was 1.6653 m^3per kg, determine the identity of the exhaust gas.
8
An oxygen tank has a volume of V = 3.00 m3. The gage pressure of oxygen in the tank is Pgage = 400.00 kPa. The room temperature is T = 27.00 ˚C and the atmospheric pressure is Patm = 100.00 kpa. The gas constant of oxygen is R = 0.25980 kPa/(kg·K). Oxygen can be treated as an ideal gas. Determine (1) the specific volume of oxygen, v =_____ m3
Steam leaves an industrial boiler at 645.3kPa and 151.2°C. A portion of the steam is fed through a throttling calorimeter and released to the atmosphere when the calorimeter pressure exceeds 104.3kPa. If the calorimeter's steam temperature is 113.8°C, a. What is the amount of moisture that is escaping from the boiler container? Show unit analysis & conversion. b. Calculate the mass of the saturated vapor if the mass of the saturated liquid is 15kg. Show unit analysis & conversion. @645.3kPa and 151.2°C: hf = 624.56kJ/kg hfg =2123.3kJ/kg @104.3kPa and 113.8°C: h2=2506.7kJ/kg
Steam generators are a type of heat exchanges that are used in power plants to generate steam at desired pressure and temperature (Fig. Q1.b). In a steam generator, saturated liquid water at 30°C enters a 60-mm diameter tube at the volume flow rate of 12 L/s. After exchanging heat with hot gas, the water changes to steam and leaves the generator at a pressure of 9 MPa and a temperature of 400°C. During this process, the diameter of the water/steam tube does not change.(iii) What is the exit velocity of the steam?
Section F 37 A sealed rig (1 m3) contains 2 kg of water (liquid PLUS vapour) at 20°C. The rig is heated until the temperature inside is 95°C. Calculate: The specific volume of the system at 20°C. (m3/kg) Type your answer. 38 Typ:-| The specific volume of the liquid at 20 °C. (m³/kg) Type your answer. 39 The specific volume of the vapour at 20 °C. (m³/kg) Type your answer.
There's a copper calorimeter container with the mass 0.2 kg and has 0.32 kg of H2O and also 0.036 kg of ice (thermal equilibrium at atm). If we drop 1.5 kg of lead at a temperature of 200 Celsius into calorimeter container, find the final temperature (in Celsius). Please show work Lead=131J/kgK Copper=390J/kg.K H2O = Cw = 4190 J/kg.K & LF = 3.34 x 105 J/kg
Subject: fluid mechanics Determine the mass of air at a pressure of 215kPa and a temperature of 31°C in a 132-gallon container.
I need step by step explanation. Please explain clearly
i. Draw a P-V graph to represent the changes undergone by the air ii. Calculate the maximum volume of the air. iii. What is the maximum pressure of the air? iv. State how the net work done on the air for the whole process can bedetermined.