B: Tikrit University has been established its electrical distribution system in a special method called RMU Ring Ni Unit) which provide the University from two power sources (VA and VB) to ensure the continuity of the power for all buildings, if VA-230 v and VB-225 v determine. 1- Where will be the point of minimum potential (voltage) according to the sources VA and VB? Then explain why? N 2- What are the highest and the lowest limits of voltages should be provided if the declared voltage is 224, in order to consider this distribution system is a good system?

B: Tikrit University has been established its electrical distribution system in a special method called RMU Ring Ni Unit) which provide the University from two power sources (VA and VB) to ensure the continuity of the power for all buildings, if VA-230 v and VB-225 v determine. 1- Where will be the point of minimum potential (voltage) according to the sources VA and VB? Then explain why? N 2- What are the highest and the lowest limits of voltages should be provided if the declared voltage is 224, in order to consider this distribution system is a good system?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What are the power quality issues in the interconnected system of solar PV and wind system
a generator and a battery whose voltages are respectively Eg=129.6 volts and Eb= 126 volts , are connected in parallel through line resistors to deliver power to a common load of 6 ohms. Line resistor for the generators is 2.85 ohms and its internal resistance is 0.15 ohms. For the battery, the line resistor is 2.8 ohms and its internal resistance is 1.2 ohms. Calculate the currents supplied by the generator and the battery, and the current taken by the load. Calculate also the load voltage Vl and the load power Pl.
2-wire DC system,
.A 2-phase circuit breaker is rated at 2000 MVA, 33kV; its making current will be a) 35 kA c) 70 k A b) 49 KA d) 89 KA
.A 2-phase circuit breaker is rated at 2000 MVA, 33kV; its making current will be a) 35 kA c) 70 k A b) 49 KA d) 89 KA
Is there any Voltage Law' for nodes? If sO, what is it? Is there any 'Current Law' for meshes? If so, what is it? Components currents references are given in the figure, any change of these current references will not affect the resulting current values, why? After the determination of the currents references, can we connect the ammeter terminals in any way in order to measure the current of a component? 1. 2. 3. 4.
23. Acurrent of i=6+ 10sin(100xt) + 20 sin(200rt) is flowing through a series combination of a PMMC and moving iron instrument. Ratio of the two currents as registered by the M.I. and PMMC meter is (a) 1.81 (c) 2.82 (b) 3.11 (d) 2.63
B: Tikrit University has been established its electrical distribution system in a special method called RMU Ring Main Unit) which provide the University from two power sources (VA and VB) to ensure the continuity of the power for all buildings, if VA= 230 v and VB= 225 v determine: 1- Where will be the point of minimum potential (voltage) according to the sources VA and VB? Then explain why? 2- What are the highest and the lowest limits of voltages should be provided if the declared voltage is 224, in order to consider this distribution system is a good system?
A manufacturing company has privately contracted your company to rewire the mechanical workshop in the building. During a site visit, you observed that the building receives a 400V, 60HZ, star-connected, three-phase supply from the utility. There are also several three-phase equipment in the workshop including bench lathes, drill presses and welding machines that require a 230V three-phase supply. You have decided to utilize three single-phase, dry type transformers to step down the building's incoming supply to a 230V, delta-connected supply for the equipment. All the three-phase machinery can be modelled as an equivalent balanced three-phase star- connected load with a resistance and inductance of 0.50 and 0.16mH respectively per phase. Some preliminary calculations and analysis are required before starting the wiring design. a) Draw a labelled diagram of the entire three phase system clearly showing all known voltages (phase and line values) and the three phase configurations of all…
1. According to KVL, the voltage supplied to a closed circuit is equal to: A. The sum of the resistances in the circuit B. OV C. The power dropped across the loads in the circuit D. The sum of the voltage drops across the loads 2. Which of the following is NOT a true statement regarding Kirchhoff's Voltage Law? A. It helps us determine unknown values at desired points in a circuit B. It is often used in combination with Ohm's Law C. It states that zero voltage can be dropped in a circuit D. It is based on the principle of the conservation of energy 3. Two circuit elements are in series when: A. They have only one common terminal B. They are connected in alphabetical order C. They have more than one common terminal D. They have the same voltage drop 4. True or false: Current is the same through all points in a series circuit. A. True B. False 5. A voltage divider receives an input voltage of 9V. If the two series resistors in the divider have the same resistance, what will the output…
Question is attached
Part b)