pls answer q ii Q2. A series of motor (Load 1) and lighting (load 2) are connected to an AC source as shownin Figure Q2. The AC source, Vs, supplies 415420° V with frequency 50 Hz. Based on thisinformation:5Ω 100 m .15ΩLoad 1Load 2i) Calculate the total load impedance. 2. '1Vsii) Calculate the current, I.Figure Q2.(iii)Write the waveform expressions in frequency domain for Vs and I. Draw a phasordiagram consists of Vs and / and state the relationship between Vs and I.(iv)Determine the power factor and calculate the real power, reactive power andapparent power. Establish the power triangle for the load.

Since you have asked only for (ii) so I have posted solution only for (ii) . This question belongs…

Q2. A series of motor (Load 1) and lighting (load 2) are connected to an AC source as shown in Figure Q2. The AC source, Vs, supplies 415420° V with frequency 50 Hz. Based on this information: 5Ω 100 m . 152 Load 1 Load 2 i) Calculate the total load impedance. 2. :'1 Vs ii) Calculate the current, I. Figure Q2.

Q2. A series of motor (Load 1) and lighting (load 2) are connected to an AC source as shown in Figure Q2. The AC source, Vs, supplies 415420° V with frequency 50 Hz. Based on this information: 5Ω 100 m . 152 Load 1 Load 2 i) Calculate the total load impedance. 2. :'1 Vs ii) Calculate the current, I. Figure Q2.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

6. Why is it important to measure Strain? 7. What is your own understanding of Young's Modulus? 8. What is the major difference between stress and strain? 9. What is the mathematical relationship between voltage and strain based on your data? 10. What is the mathematical relationship between voltage and stress based on your data?
EENG250 Midzerm - Spring 2021 × This course Clear my choice Find RAB in the circuit shown. 12 k2 2 kN 6 kQ RAB 4 k2 12 kQ BO Select one: O a. 2 K O b. None of them O c.6K O d. 12 K O e. 4 K
i need the answer quickly
15052 15ar A 2002 $20 3502 Find Vth and Rth for the circuit shown at nodes A and B. Do NOT include u in your answer. Vth: Volts Rth: Ohms
The loads on a 300-meter ring distributor are depicted in figure 2.1 (a), where the distances are given in metres. Each conductor has a resistance of 0.20 per 1,000 metres, and the loads that are tapped off at points B, C, and D are as shown in the diagram. Determine the voltages at B, C, and D given that the distributor is fed at point A. 50 A 70 1 240 V A (a) 60 B 70 A 100 A 80 50 A 91A D T 41 A 220 V A (b) 129 A B 100 A 729 A 70 A
A series RLC circuit, which is driven by a variable frequency and 2 A current source, has the following values: R=1 Kn, L=100 mH and C= 10 µF. Find the bandwidth of the network? 1000 0.1 None of the answers 100
21 V1 R2 Va k V3 2A 4V Vo analysis to determine the voltage at the node V2 in Volts. For the above circuit, with R1-6 Ohms and R2" 2 Ohms, use no Round your answer to the nearest single digit decimal place. For example, if you calculate 3.27 Volts, then enter 3.3 as your answer. A Moving to another question will save this response. P Type here to search
Thank you And please kindly write legibly because I'm having a hard time reading, guessing, and understanding the handwriting of different experts recently. Thanks Please refer to the photo below. Activity: Series and Parallel Capacitance
Please help with 1 and 2 1.Use kirchhoff's laws to determine the current 2. Determine the power supplied by the dependent source. Use voltage division
None
%TV l. M E O O A:09 docs.g هدی عبدال له عبدال. . . B2/for the figure b rv+ shaded Area : * 3 cm y=kx? 8 cm 7 cm 6 cm 49.23 51.66 50.76 45.32 47.81 53.22 B2/(b) X-bar * 3 points II
b) Indicate the following characteristics on the generic second order response given in Figure Q3(b). i. ii. iii. iv. Rise Time Settling Time Min Settling Time Max Settling Time V. Overshoot vi. Undershoot vii. viii. Maximum peak Peak Time Amplitude 4 3.5 3 2.5 2 1.5 H 1 0.5 0 0 5 Step Response ܫܚܢ 10 Time (seconds) Figure Q3(b) 15 20 25