B P/2. P/2 5 in. 8 in.

Q: Assuming that P = 48 000 N and that it may be applied at any joint on the line FJ, determine the…

A: There will be tension 'T' in the rope/member  attached to joint E and a vertical reaction (upwards)…

Q: Determine the external reactions at A and F for the roof truss loaded as shown (positive answers are…

A:

Q: hine the magnitude of F2 which will cause the reaction C, at the bearing C to be equal to zero. The…

A:

Q: (1) A B

A: for solution refer below images.

Q: The bent rod is supported at A. B, and C by smooth journal bearings as shown in (Egure 1)

A:

Q: A six-pack is shaken so that the pressure in each can is p = 20 psi. A board is placed on the six…

A: Write the given information.

Q: Determine the external reactions at A and F for the roof truss loaded as shown. The vertical loads…

A: Let horizontal and vertical reactions at hinge support A are RAX and RAY respectively. Let vertical…

Q: The boom is used to support the 100-lb flowerpot. The boom is held in place by a ball-and- socket…

A:

Q: * The stacking ABAB is for FCC crystal structure BCC crystal structure HCP crystal structure O

A: BCC does not have any stacking sequence.

Q: The 58-mm-diameter cylinder is made from Am 1004- T61 magnesium and is placed in the clamp when the…

A:

Q: Two rods of diameter d = 3 in are joined together: a C83400 brass rod, and a 2014-T6 aluminum rod.…

A:

Q: Determine the force in the rod AB caused by the increase in temperature. Express your answer to…

A:

Q: 4-69. Three bars each made of different materials are connected together and placed between two…

A: Given that:For Steel,For Brass,For Copper,

Q: Please solve the problem in a sheet of the paper and draw the free body diagram.

A:

Q: The member shown is pin-connected at A and rests against a smooth support at B. Determine the…

A:

Q: The stepped rod shown in the figure is made of Al 2014-T6 aluminum alloy. At temperature TI = 20°C,…

A: Given: Al 2014-T6 material; therefore E=73 GPa α=23x10-6 /degC Force at B = 20kN To find: reactions…

Q: The bucket at (x,y,z) = (2.2, 2.9,0) is supported by 3 slender bars as shown and is in equilibrium.…

A:

Q: Determine the external reactions at A and F for the roof truss loaded as shown (positive answers are…

A: To find: The external reaction at A and F. Free body diagram: The free body diagram shown below:

Q: A steel rod is bent to form a mounting bracket. For each of the mounting brackets and loading shown,…

A:

Q: ted together and placed between two walls when the ature is T = 12 C. Determine the force exerted…

A:

Q: Find the maximum friction force and determine whether the block is in equilibrium when e = 20° and P…

A:

Q: Determine the vertical force P that must be applied at C to maintain the equilibrium of the linkage.…

A: Determine the vertical force P that must be applied at C to maintain the equilibrium of the linkage.…

Q: The 50-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed in the clamp when the…

A: Diameter of the cylinder made of the magnesium: Initial temperature of the clamp: Diameter of the…

Q: The 19-lb weight is supported by the cord AC and roller and by a spring. If the spring has an…

A:

Q: The 58-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed in the clamp when the…

A:

Q: The 56-mm-diameter cylinder is made from Am 1004- T61 magnesium and is placed in the clamp when the…

A: Given:

Q: If the temperature of the 85 mmmm diameter post CD is increased by 60 ⚫C, determine the force…

A:

Q: Consider the following figure where the load P = 900 N.  Determine the components of the…

A: Step 1:Step 2:  Hope this helps!

Q: The 0.35-inch-diameter cylinder is made from C83400 red brass and is placed in the device depicted…

A: inlet diameter (d)= 0.35 inch  Temperature (T1)= 50 F other diameter ( D)= 0.10 inch

Q: B D F Ag C E G P1 P2 P3 8 A8 A8 A8 ft ft→ H T 6 ft Draw the free-body diagram of the panel ABC, FGH,…

A: Free-body diagrams with explanation was

Q: force of P=180lb supports a 300lb box in an inclined plane as shown. Determine the angle at which it…

A: Given: To determine the angle of slope for the box to remain in equillibrium. P=180 lb W=300 lb

Q: The 50-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed in the clamp when the…

A: Introduction In order to determine the temperature at which the normal stress achieves the specified…

Q: The assembly shown consists of two A992 steel bolts AB and EF and junction of 6061-T6 aluminum and…

A: Length of steel rod = 400 mm Length of Aluminium rod = Length of brass rod = 150 mm Coefficient of…

Q: Determine the components of the reactions at A and E if a 1080-N force directed vertically downward…

A: Step 1:Step 2:

Q: Using the method of sections, determine the internal force in members EF and EG. Indicate if the…

A:

Q: rmine the magnitude of the horizontal component of the reaction at point A if F=287N , a=0.44m,…

A:

Q: The 50-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed in the clamp when the…

A: For Am 1004-T61 magnesium                 αmg=26×10-6/°CEmg=44.7 × 103MPa For 304-stainless-steel…

Q: 2. Which of the following shows the correct equilibrium equation in the direction parallel to the…

A: Force applied by Ross parallel to inclined plane=150N Force applied by Rachel normal to inclined…

Q: The bar has a cross-sectional area A, length L, modulus of elasticity E, and coefficient of thermal…

A: From the figure, it's clear that total displacement is zero.                  δT-δF=0δT=δF…

Q: P2 P1 B. 4 ft F31- -3 ft- -3 ft- -3 ft-

A: Free body diagram: Consider the equillibrium of moments about…

Q: The 50-mm-diameter cylinder is made from Am 1004- T61 magnesium and is placed in the clamp when the…

A:

Q: determine the force in

A: Here We need to determine the Force in cylinder when temperature goes to T2= 130 deg.c

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.