(1) A B

Q: Carriage is mounted on the outer guide ways of lathe bed and it can move in a direction parallel to…

A:

Q: which are the main instrucations used in FAPT-TURN? Cutting area definition?

A: The instruction used in FAPT-TURN can be given as,

Q: In Drilling machine, Feed given to drill in this direction makes the hole Select one: a. Downward b.…

A: Given :-  In Drilling machine, Feed given to drill in this direction makes the hole Select one: a.…

Q: Question 1 Compute the lead of a 4 -19 UNC single t

A:

Q: Identify the number of spur gears available in a Single Purchase Crab Winch a. One b. Three c. Four…

A:

Q: Complete the following table for 7 types of Engineer’s Hammers.        Types                 Hand…

A:

Q: is used to cut machine other material. O Chromium steel Nickel steel O Martensitic tool steel O Tool…

A: To find the material that are used to cut machine other material .

Q: Angle between side cutting edge and axis of tool is known as: * Back rake angle Side rake angle Side…

A:

Q: O b. tail stock O c. bed

A: Given Data→ Housing Driving pulleys Back gears

Q: The __________ square has a moveable inch-graduated blade. Select one: A. SPEED SQUARE B. FRAMING…

A: The combination square has a movable inch graduated blade.

Q: In Drilling machine, Feed given to drill in this direction makes the hole Select one: O a. 45 degree…

A: Drilling is a cutting operation in which a drill bit is used to cut a circular hole in a solid…

Q: cutting edge a

A: ANSWER- SIDE CUTTING EDGE ANGLE

Q: From the following Identify cutting tool made by forging before hardening and grinding. О а. Ob. О…

A: First step for making a tool is

Q: The following tool is used to cutting internal threads of drilled hole Select one: a. Drill plate b.…

A: It is required to which tool is used to cutting internal thread of drilled hole

Q: QUESTION 2 If you have to precisely rotate your workpiece, which is held on an indexing head, by a…

A:

Q: Up milling operation is performed for finishing cut. Select one: True False

A:

Q: During drilling operation, work piece must be held in vice. Select one: True False

A: Given Statement : During drilling operation, work piece must be held in vice. Select one: True…

Q: For a triple start thread, lead is ----- the pitch a. equal to four times O b. equal to twice c.…

A: Lead Lead is defined as the distance covered along the screw axis when one complete rotation is…

Q: In a single cylinder reciprocating engine, the primary unbalanced force is maximum

A: In a single cylinder reciprocating engine, there is one primary and one secondary unbalanced force.

Q: From the following Identify cutting tool formed by grinding the end piece of a steel stock is O a. O…

A: Option d is correct.

Q: True or False: The BREAK command requires two separate points when breaking a circle.

A: The BREAK command is used to break the selected object between two points.

Q: 5. Name a tool that can be used to check an internal thread.

A: In this problem, it is asking about the name of the tool that can be used to check an internal…

Q: It is only required to move the cutting tool from the circumference to the center of the workpiece…

A: Introduction A milling machine is a machine that removes material from a workpiece by feeding it…

Q: 6. Approximate a spindle speed of 1000 rpm into rad/s. Spindle diameter = 200 mm 2.25 rad/s .16 mm/s…

A:

Q: голь 40° Find P. do, 25°

A:

Q: A'4- point socket has a drive size of 0.5 inch. Which dimension does this denote? C. Radius of the…

A: A'4- point socket' has a drive size of 0.5 inch means the side of the square is 0.5 inches.

Q: Which set of ordered processes best describes the steps to perform an emergency stop and reset of…

A: A lathe machine is used for the turning, facing, drilling, and surface finishing processes of…

Q: Center drilling operation performed on lathe machine uses a single-point cutting tool. Select one:…

A: Answer is false

Q: When it comes to finding the moment arm, you must use the distance of the line from the pivot to the…

A: Explanation When it comes to finding the moment arm, you must use the distance of the line from the…

Q: What kind of endmill has many smaller teeth meant to distribute the load to reduce vibration during…

A: Select the endmill as below features: Utilize a bigger endmill with a bigger center measurement.…

Q: Give at least 5 purpose of cutting internal threads by the use of Lathe Machine

A: given; Give at least 5 purpose of cutting internal threads by the use of Lathe Machine.

Q: Name the operation which is enlarges the top portion of drilled hole with tapered shape? a. Step…

A: The process of creating a V-shaped tapered edge near the surface of a hole is known as…

Q: Draw three views of the adjusting bracket. Drill-2 Holes Drill PROB. 20 Adjusting bracket.

A: Given isometric view of the adjusting bracket  To sketch the three views  Below the three views are…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.