The 58-mm-diameter cylinder is made from Am 1004- T61 magnesium and is placed in the clamp when the temperature is T₁ = 20°C. (Figure 1) Figure 100 mm 1 of 1 150 mm Part A If the 304-stainless-steel carriage bolts of the clamp each have a diameter of 9 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the force in the cylinder when the temperature rises to T₂ = 130°C. Express your answer to three significant figures and include the appropriate units. F = Submit uА Value Provide Feedback Request Answer Units ? Nex

The 58-mm-diameter cylinder is made from Am 1004- T61 magnesium and is placed in the clamp when the temperature is T₁ = 20°C. (Figure 1) Figure 100 mm 1 of 1 150 mm Part A If the 304-stainless-steel carriage bolts of the clamp each have a diameter of 9 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the force in the cylinder when the temperature rises to T₂ = 130°C. Express your answer to three significant figures and include the appropriate units. F = Submit uА Value Provide Feedback Request Answer Units ? Nex

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A rod, 45 mm in diameter and made of Red Brass, is fixed to the wall at A. There is a gap of 1.5 mm from the free end B to another wall. You are required to determine the change in temperature (AT) required to cause the rod to buckle. Assume that B acts as a pin support when contact is made. A B 1.5 m 1.5 mm
The 50-mm-diameter cylinder is made from Am 1004- T61 magnesium and is placed in the clamp when the temperature is T₁ = 15°C. (Figure 1) Figure 100 mm Part A If the two 304-stainless-steel carriage bolts of the clamp each have a diameter of 10 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the temperature at which the average normal stress in either the magnesium o the steel first becomes 14.5 MPa Express your answer to three significant figures and include the appropriate units. T₂ = Submit ¸μA Value Provide Feedback Request Answer Units Review ? Next >
At a temperature of 20 °C there is a gap ∆ = 0.2 mm between the lower end of the brass bar and the slab rigid suspended from the two steel bars. Neglecting the mass of the slab, determine the stress in each bar when the temperature of the assembly rises to 100°C Answer: σsteel = 15.462MPa (t), σbronze= 20.615MPa(c),
Review Part A The 50-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed in the clamp when the temperature is T = 20°C. (Figure 1) If the 304-stainless-steel carriage bolts of the clamp each have a diameter of 12 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the force in the cylinder when the temperature rises to T2 = 130°C. Express your answer to three significant figures and include the appropriate units. HA F = 1301.4 Figure 1 of 1 Submit Previous Answers Request Answer 100 mm 150 mm Provide Feedback Next >
A solid 0.25-in.-diameter cold-rolled steel rod is pinned to fixed supports at A and B. The length of the rod is L = 25 in., its elastic modulus is E = 32000 ksi, and its coefficient of thermal expansion is a = 6.5 x 10-6 in./in./°F. Determine the temperature increase AT that will cause the rod to buckle. P L B Answer: AT = i O
The rigid bar AC is supported by two axial bars (1) and (2). Both axial bars are made of bronze [E = 100 GPa; a = 18 × 10-6 mm/mm/ °C). The cross-sectional area of bar (1) is A1 = 184 mm2 and the cross-sectional area of bar (2) is A2 = 380 mm2. After load P has been applied and the temperature of the entire assembly has increased by 38°C, the total strain in bar (2) is measured as 1240 µɛ (elongation). Assume L1 = 1290 mm, a = 590 mm, b = 820 mm, and L2 = 2000 mm. Determine: (a) the magnitude of load P. (b) the vertical displacement of pin A. L2 (1) L1 B a P Answers: (a) The magnitude of P = i kN. (b) The vertical displacement of pin A = i mm (down).
The rod is made of A-36 steel and has a diameter of 0.25in. If the rod is 4ft long when the springs are compressed 0.5in and the temperature of the rod is T=40°F, determine the force in the rod when its temperature is T=160°F. k= 1000 lb/in. ww 4 ft k = 1000 lb/in. WW
A solid 0.48-in.-diameter cold-rolled steel rod is pinned to fixed supports at A and B. The length of the rod is L = 20 in., its elastic modulus is E = 30000 ksi, and its coefficient of thermal expansion is a = 7.2 x 10-6 in./in./°F. Determine the temperature increase AT %3D %3D that will cause the rod to buckle. A L B Answer: AT =
The assembly shown consists of two A992 steel rods AB and EF and an 6061-T6 aluminum rod CD. When the temperature is at 30° C, the gap between the rod and rigid member AE is 0.1 mm. Determine the following: a) The temperature to which the rod CD just touches member AE such that no axial stress is produced in any rod. b) The highest temperature to which the assembly can be raised without causing yielding (that is, yield strength is not exceeded) in any rod. Assume BF is also rigid and ignore the portion of steel rods within the rigid members. 300.1 mm 25 mm 50 mm D 0.1 mm 300 mm E 25 mm
The rigid bar ABC is supported by a pin at B and two vertical steel rods. Initially the bar is horizontal and the rods are stress-free. Determine the stress in each rod if the temperature of the rod at A is decreased by 40° C. Neglect the weight of bar ABC. Use a 11.7 x 10-6/°C and E 200 GPa for steel. A = 1200 mm. A 300 mm² 1.2 m 0.9 m C A. 0.6 m- 1.2 m