(b) In the diagram below Fig Q2(b), forces are applied along three different axes to a 100 mm cube ofaluminium, denoted as resulting in a uniform stress of 5.5 GPa, applied uniformly across theentire surface area of each face.Cube withcross-sectionarea AFig Q2(b)Symbol for modulusAluminiumK62 GPa69 GPa24 GPaG(1) Identify the appropriate modulus of elasticity to be applied and explain why.Using the correct modulus, determine the percentage volume change for the cube, comparedto its original volume.

This question is based on Mechanical Properties of Solids topic. Bulk Modulus is the ration of Bulk…

(b) In the diagram below Fig Q2(b), forces are applied along three different axes to a 100 mm cube of aluminium, denoted as resulting in a uniform stress of 5.5 GPa, applied uniformly across the entire surface area of cach face. Cube with cross-section F area A Fig Q2(b) Symbol for modulus Aluminium K 62 GPa 69 GPa 24 GPa E G (i) Identify the appropriate modulus of elasticity to be applied and explain why. Using the correct modulus, determine the percentage volume change for the cube, compared to its original volume.

(b) In the diagram below Fig Q2(b), forces are applied along three different axes to a 100 mm cube of aluminium, denoted as resulting in a uniform stress of 5.5 GPa, applied uniformly across the entire surface area of cach face. Cube with cross-section F area A Fig Q2(b) Symbol for modulus Aluminium K 62 GPa 69 GPa 24 GPa E G (i) Identify the appropriate modulus of elasticity to be applied and explain why. Using the correct modulus, determine the percentage volume change for the cube, compared to its original volume.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s- 300, in units of 10° Nim?. What are (a) the Young's modulus and (b) the approximate yield strength for this material? Assume e- 0.010. 26 Strain (a) Number i Units (b) Number Units (G/N 01) wang
The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s = 290, in units of 106 N/m². What are (a) the Young's modulus and (b) the approximate yield Assume ε = 0.0090. strength for this material? (a) Number i (b) Number Stress (106 N/m²) In Units Units Strain 28
answer in whole number, scientific notation is not allowed
The total cross-sectional area of the load-bearing calcified portion of the two forearm bones (radius and ulna) is approximately 2.0 cm2. During a car crash, the forearm is slammed against the dashboard. The arm comes to rest from an initial speed of 80 km/h in 4.5 ms. If the aum has an effective mass of 3.0 kg, what is the compressional stress that the arm withstands during the crash? Pa Need Help? Read It
the point that identifies the proportional limit of the material whosee graph of stress as a function of strain is shown as?
A sphere of copper has a radius of 8.00 cm and is compressed uniformly by a force of 5.00 × 108 N. The bulk modulus for copper is 140 x 10⁹ N/m². Calculate the sphere's change in volume AV after compression. Calculate the sphere's final radius R. AV = R = 3.81 x107 Incorrect 0.075 -7 Incorrect m³ m
A firefighter weighs 730 N. She wears shoes that each cover an area of 309cm2. (a) What is the average stress she applies to the ground on which she is standing? (b) How does the stress change if she stands on only one foot? Show working equations for both (a) and (b). Answer must be in kPa.
Assume that if the shear stress in steel exceeds about 4.00 x 108 N/m², the steel ruptures. (a) Determine the shearing force necessary to shear a steel bolt 1.40 cm in diameter. IN (b) Determine the shearing force necessary to punch a 1.25-cm-diameter hole in a steel plate 0.550 cm thick. N
Consider a square-faced beam supporting a section of a building. a) Before installation, the length of the beam is found to be l0 = 15.02 m (figure a). After installation and construction, the length is remeasured and found to be l = 14.98 m (figure b). Determine Young's Modulus Y in N/m2 for the beam if it supports a mass m = 35000 kg and has a side length d = 1.9 m. b) Suppose that after the beam is installed it needs to be repaired. The weight it supports is removed and replaced with a new mass m2 (figure c). After the new mass is supported, the side length is remeasured and found to be larger with a difference of Δd. Assuming that this side length deformation is uniform and small, write an expression for determining Poisson's ratio v for this beam if its Young's modulus Y is known.
The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s = 300, in units of 106 N/m². What are (a) the Young's modulus and (b) the approximate yield strength for this material? Assume & = 0.0010. (a) Number (b) Number 1.5E11 Hint 3E8 eTextbook and Media Stress (10 N/m²) E Strain Units 28 N/m^2 or Pa Units N/m^2 or Pa SUPPORT
The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s = 350, in units of 106 N/m². What are (a) the Young's modulus and (b) the approximate yield strength for this material? Assume ε = 0.010. (a) Number i (b) Number i Stress (106 N/m²) Units Units E Strain 2ɛ <
A rod has a length 2.00000 m at 10.0°C. The length of the rod increases to 2.00060 m when the temperature increases to 30.0°C. What is the coefficient of linear expansion of the material from which the rod is made?