firefighter weighs 730 N. She wears shoes that each cover an area of 309 cm2. (a) What is the average stress she applies to the ground on which she is standing? (b) How does the stress change if she stands on only one foot? Show working equations for both (a) and (b). Answer must be in kPa.

Q: 0.25 in. 5 in. 1 in. 0.25 in. -0.25 in. 2.5 in.

A: Maximum axial force P that can be applied to the steel plate

Q: The elevator in a vertical mine shaft is supported by a steel cable of cross-sectional area 3.20 x…

A:

Q: The wood beam has an allowable shear stress of Tallow = 5 MPa. (Figure 1) Figure 50 mm 50 mm 50 mm…

A:

Q: A vertical solid steel post of diameter d = 26 cm and length L = 2.70 m is required to support a…

A: The objective of the question is to calculate the stress and strain in a steel post supporting a…

Q: A 22.0 m long aluminum cable with a cross-sectional area of 2.04 x 10-3 m2 is used to suspend a 4.00…

A: Using the help of Young's modulus we will solve the given question. Given(s): Length of the cable,…

Q: a wire of radius 0.2 x 10^-3 m is suspended from the ceiling.When a weight (force) of 5.0N is…

A: Given, Weight (force) hanging,F=5 N Radius of wire, r=0.2×10-3m

Q: The Young’s modulus for steel is at most 215 GPa (1 GPa= 109 N/m2).  If you apply a force of 50.0…

A: Given quantities: Young's modulus of steel (Y) = 215 GPa Applied force (F) = 50 GPa initial length…

Q: A 226-N object is hung from the end of a wire of cross-sectional area 0.03 cm-. The wire stretches…

A: Given: Force,F=226NArea,A=0.03cm2=0.03×10-4m2Length,L=150cm=150×10-2mChange in…

Q: The total cross-sectional area of the load-bearing calcified portion of the two forearm bones…

A: Given that -  Mass Velocity Cross sectional area To Find - We have to determine the required…

Q: 7. A 6.0 m cylindrical steel beam 3.50 cm in diameter supports an overhead walkway. The beam is…

A:

Q: A hydraulic press contains 0.25m^3 of oil. It is subjected to a pressure increase of 1.6x10^7 Pa.…

A: Have a look at solution dear

Q: (LO2-4) If b = 1 (i.e. the anchor side of the cable is at a 45° angle), what should be the slope a…

A:

Q: Q. A rod having a diameter of 4 cm and length of 1 m is suspended from a rigid suppor as shown in…

A: Youngs modulus of elasticity     Y = stress /strain

Q: A homogeneous 800 kg bar AB is supported at either end by a cable as shown in the figure below.…

A: Draw free body diagram of the system.

Q: An aluminum specimen 15 in long and in in diameter is subjected to tensile stress. The new length of…

A:

Q: A 586-N object is hung from the end of a wire of cross-sectional area 0.04 cm2. The wire stretches…

A:

Q: Blue Brass wire is 4 m long and 4 mm in diameter that is hanging from ceiling. If there's a mass of…

A: length = 4 m diameter = 4mmradius = 2mmmass = 5kg stretching amount = 0.16mm

Q: A vertical solid steel post of diameter d = 26 cm and length L = 2.70 m is required to support a…

A:

Q: An 800Kg lift is suspended by a steel cable whose allowable stress is 1.2x10^8N/m^2. What is the…

A: Given that,  The mass of the lift, m is 800kg. The allowable stress on the steel cable, σ is 1.2×108…

Q: The beam is supported by a pin at A and a short link BC. Figure 0.5m 1 m 4P 1.5 m 4P 1.5 m 0.5m 1 of…

A:

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

A:

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by…

A: Given :  scale of the stress axis is set  as s=320 in a unit of 106N/m2 ε=0.0090

Q: Young's modulus for compression of human bone is approximately 9x10⁹ N/m^2. Assume that a femur has…

A: Given in question :  Young's modulus (Y) = 9 x 109 N/m2  Stress (S) = 7.5 x 107 N/m2  Length of the…

Q: An aluminium (p = 2.7g/cm³) wire is suspended from the ceiling and hangs vertically. How long must…

A: Given that-Density of aluminium wire, ρ=2.7g/cm3Stress at upper end, σt= 8×107 N/m2We know…

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

A:

Q: Let A be the last digit and let B be the second to last digit of your 8-digit student ID.  A steel…

A: Mass of object  =  139.8 kgExplanation:

Q: The perimeter forming rate of the 45 ° jet shown in the figure is calculated when the strain rates…

A:

Q: For the connection shown, the average shear stress in the 19-mm-diameter bolts must be limited to…

A:

Q: A ceramic rod tensile test is applied to the cylinders and the strain value during tensile is…

A: Given that:Longitudinal strain, dL/L = 0.2%=2×10-3Lateral strain, dr/r =0.5× 0.04%=…

Q: The plot of tensile stress vs tensile strain of a certain rod has a slope of 25-GPa in the elastic…

A:

Q: A 242-N object is hung from the end of a wire of cross-sectional area 0.01 cm2.  The wire stretches…

A:

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set bys =…

A: s = 350 ×106 Nm2ε = 0.010

Q: A 115 m long steel cable with a cross-sectional area of 1.13 x 10-4 m2 is subjected to a tensile…

A: Given- Length L= 115 m Cross-sectional area A= 1.13 x 10-4 m2  Tensile force F= 565 N

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s -…

A: Given: S = 300 in units of 106 N/m2 ε = 0.010   Solution: a) From the given graph, we have…

Q: The total cross-sectional area of the load-bearing calciried portion or the slammed against the…

A:

Q: a 1,460-N uniform beam is attached to a vertical wall at one end and is supported by a cable at the…

A:

Q: Assume a human leg contains a 50cm long bone with an average cross section of 3cm. By how much (in…

A:

Mechanical Properties of Solids

There are three types of matter- solid, liquid and gas. Out of them, solids have a rigid shaped and size. The intermolecular forces of attractions in solids are greatest. Mechanical properties are the physical properties of a material which it shows, when it is provided with certain amount of force or load. These properties are to be kept in mind for various purposes. When a force is applied to an object, the object may or may not get deformed depending upon its elastic property. But every time the object develops a restoring force against the force applied. This is commonly known as stress. If the object changes its dimensions due to the force applied it develops strain ( which is the ratio of change in dimension to the original dimension).