A shear force of 350 N is applied to one face of an aluminum cube with sides of 30 cm while the opposite face is held fixed in place. What is the resulting displacement of the face? (The shear modulus for aluminum is 2.5 × 1010 N/m2)

Q: A steel cube of side length L = 0.5 m is subjected to a shearing force of 5000 N along the top…

A: Length=0.5m Shear force=5000N Shear constant=8.3×10^10N/m2 Shearing angle=?

Q: The unknown metal cube measures 4.2 x 10 ― 2 m has a stress of 9.2 x 1011 N/m 2 and a change of…

A:

Q: A steel cube of side length L = 0.5 m is subjected to a shearing force of 5000N along the top…

A:

Q: One end of a steel rod of radius R = 10mm and length L = 90 cm is held in a vise. A force of…

A:

Q: The ultimate strength of a metallic wire for tension is 2.0 x10^8 Pa. The wire was set up with a…

A: Given: s=2.0*108 Pad = 0.5 cm = 0.005 mM = 200 Kg

Q: A solid cube of side 0.1 m is subjected to a shearing force of 1000 N. The top surface of the cube…

A: To find-(1) shearing stress(2) shear srain(3) modulus of rigidityGiven-F=1000 NL=0.1 mx=0.22×10-3…

Q: A high-carbon steel wire, circular in cross-section, has a diameter of 14 mm. What is the force (in…

A:

Q: A uniform metal bar, one metre long, is placed symmetrically on two knife-edges separated by a…

A: We can use the formula for the deflection of a uniformly loaded beam supported at its ends: δ =…

Q: A bar of length 100 cm is supported a its two ends. The breadth and depth of bar 5 cm and 0.5 cm…

A: To find-Depression produced in the bar (δ)=?Given-length (l)=100 cm=1 mBreadth (b)=5 cm=5×10-2…

Q: A metal slab of side (74+ 75) cm and thickness (74 + 25) cm is subjected to a tangential force of…

A:

Q: A cylindrical beam has a diameter of 1.8 m and a shear modulus of 1.0 x 1010 N/m2 projects out a…

A: Given, diameter of a cylinder beam is d=1.8m so the radius of the cylinder beam is r=0.9m shear…

Q: A solid copper cube has an edge length of 89.3 cm. How much stress must be applied to the cube to…

A:

Q: The bulk modulus of a material is 1.0 × 1011 N/m2. What fractional change in volume does a piece of…

A: Given Data: The bulk modulus is, β=1.0×1011 N/m2 The increase in bulk stress is, Δp=107 N/m2   The…

Q: A mineshaft has an ore elevator hung from a single braided cable of diameter 2.5 cm. Young’s modulus…

A:

Q: A tangential force of 0.004 KN affected the upper surface of a rectangle 5 mm high, 3 cm long and 5…

A: Given Dimensions, l=3 cm= 3×10-2mw=5 cm=5×10-2mh=5mm=5×10-3m Tangential force, F=0.004 KN= 4N…

Q: A body of mass 500 kg is suspended at the free end of an iron wire of length 3 m and cross-sectional…

A:

Q: A bar of length 100 cm is supported at its two ends. The breadth and depth of bar 5 cm and 0.5 cm…

A: We have to find the depression produced in the bar. Area, A=5 mm2=5×10-6 m2, Length, L=100 cm=1 m,…

Q: A short timber post of rectangular section has one side twice the other. It contracts by 0.05 cm/m.…

A:

Q: The leg bone (femur) breaks under a compressive force of about 8.20 × 104 N for a human and 11.7 ×…

A: Compressive force for human bone ( F human ) = 8.20 × 104 N Compressive force for horse bone ( F…

Q: A bob of mass 30 kg hangs from a copper wire ( Y= 11x10 ^10 N/m^2). The wire has an initial length…

A:

Q: A bar of length its two ends. The breadth and depth of bar 5 cm and 0.5 cm respectively. A mass of…

A: Using formula of bending of beam we will be able to find the depression produced within the beam

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

A: The stress versus strain curve is given for a material the stress is plotted along the vertical axis…

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s=…

A: The stress-strain curve is shown below.

Q: Suppose a person’s femoral diaphysis is idealized as a circular cylinder with a periosteal diameter…

A:

Q: To compress a liquid by 10 % of its original volume, the pressure required is 2 x 105 N/m². The bulk…

A: We are aware that K is the necessary pressure to compress a liquid by 10% of its initial volume.We…

Q: A tunnel of length L = 130 m, height H = 9.4 m, and width 5.6 m (with a flat roof) is to be…

A: L = 130 m, height H = 9.4 m, and width 5.6 m (with a flat roof) is to be constructed at distance d =…

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

A:

Q: he steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the shear stress…

A: Given: τallowable=70029645 Paϕall =2.24oϕall =2.24×π180ϕall =0.0390τallowable=70.029645×106…

Q: The right end of a horizontal beam of mass 4kg and length 3.3m is fixed to a wall by a hinge. The…

A: This is a problem regarding the equilibrium of forces and torques. The figure for the problem can be…

Q: The figure shows an approximate plot of stress versus strain for a spider-web thread, out to the…

A: We  have,  stress=forcearea and                strain=change in lengthoriginal lengthHence,  work…

Q: Consider a steel bolt as a cylinder with a diameter of 3.41 cm and length of 13.8 cm. A shear or…

A: diameter of 3.41 cm  length of 13.8 cm shear stress of 313 MN/m ² shear Modulus Ssteel =G= 8.4×…

Q: A solid copper cube has an edge length of 80.8 cm. How much stress must be applied to the cube to…

A:

Q: A 242-N object is hung from the end of a wire of cross-sectional area 0.01 cm2.  The wire stretches…

A:

Q: The legs of a weight lifter must ultimately support the weights he has lifted. A human tibia…

A: Given data- For human tibia (shinbone) outer diameter Dout=3.6 cm=0.036 m inner diameter Din=2.5…

Q: A wooden "2 x 4" has a cross-sectional area of 38 mm x 89 mm. The shear modulus of the wood is 1.1 x…

A: Given that:

Q: A 73-kg snow skier is being pulled up a 19° slope by a steel (Young's modulus 2.0 x 10¹1 N/m²)…

A:

Q: A 1.2 x 10-³-kg house spider is hanging vertically by a thread that has a Young's modulus of 4.4 x…

A:

Q: A tunnel of length L = 180 m, height H = 9.4 m, and width 6.1 m (with a flat roof) is to be…

A:

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

A: The relation between stress and strain is given by  Y=stressstrain Where Y is the Young's modulus of…