Answered: A bar of length 100 cm is supported a… | bartleby

Related questions

Question

A bar of length 100 cm is supported at
its two ends. The breadth and depth of bar
5 cm and 0.5 cm respectively. A mass of 100 gm
is suspended at the centre of bar. Compute the
depression produced in the bar (Y = 4 × 1010 N
/m²).

Expert Solution

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

A 195-kg load is hung on a wire of length of 3.30 m, cross-sectional area 2.000 x 10-5 m2, and Young's modulus 8.00 x 1010 N/m2. What is its increase in length?
A cube of unknown material is 0.200 m on each side and has a mass of 17.6 kg. It is suspended in a vat of honey (densityh = 1.42 x 103 kg/m³) so that its top surface is at a depth of 2.00 m below the surface of the honey (see figure-not to scale). If the fishing line has a scale attached, what would the scale read (in Newtons) while the cube is suspended in honey? th =D0 h = 2.0 m
The legs of a weight lifter must ultimately support the weights he has lifted. A human tibia (shinbone) has a circular cross section of approximately 3.6 cm outer diameter and 2.5 cm inner diameter. (The hollow portion contains marrow. ) if a 90 kg lifter stands on both legs, what is the heaviest weight he can lift without breaking his legs, assuming that the breaking stress of the bone is 200 MPa?
Between each pair of vertebrae in the spinal column is a cylindrical disc of cartilage. Typically, this disc has a radius of about 3.2 x 102 mand a thickness of about 1.2x 10 m. The shear modulus of cartilage is 1.2x 10 N/m2. Suppose a shearing force of magnitude 20 N is applied parallel to the top surface of the disc while the bottom surftace remains fixed in place. How far does the top surface move relative to the bottom surface? Number Units
phy
A high-speed lifting mechanism supports a(n) 860-kg object with a steel cable that is 38.0 m long and 4.00 cm2 in cross-sectional area. (a) Determine the elongation of the cable. (Enter your answer to at least two decimal places.) mm (b) By what additional amount does the cable increase in length if the object is accelerated upwards at a rate of 3.5 m/s?? mm (c) What is the greatest mass that can be accelerated upward at 3.5 m/s if the stress in the cable is not to exceed the elastic limit of the cable, which is 2.2 x 108 Pa? kg Need Help? Read It
A vertical steel girder with a crosssectional area of 0.15 m2 has a 1550 kg sign hanging from its end. (Ignore the mass of the girder itself.) If the girder is 9.50 m long, how much is it lengthened? Note that the Young’s modulus =200×10 9
A 3.0 m long cylindrical alloy beam is 21 cm in radius. It is found to stretch by 1.5 cm under a tension of 2.0 kN. Find its Young’s modulus.
A 2×12 board of airdried Southern Yellow Pine (~12% moisture) is about 2.18 kg per linear foot. A physicist and his wife carry a 16-foot length of Southern Yellow Pine lumber, the physicist gallantly carries the board from one end while his wife carries the board 4 feet from the other end. How much weight is each spouse carrying? This is an equilibrium problem. Assume the board is perfectly uniform.
The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s = 310, in units of 106 N/m². What are (a) the Young's modulus and (b) the approximate yield strength for this material? Assume ε = 0.010. (a) Number i (b) Number IN i Stress (106 N/m²) Units Units E Strain 2ɛ
One end of a steel rod of radius R = 9.5 mm and length L = 81 cm is held in a bench vise. A force of magnitude F = 62 kN is then applied perpendicularly to the end face(uniformly across the area) at the other end, pulling directly away from the bench vise.(Given: Young’s Modulus for stainless steel is 2.0 ×1011N/m2) Calculate the following;(i) Stress on the rod.(ii) Elongation, ΔL in the rod.(iii) Strain of the rod.
A plank 2.00 cm thick and 15.0 cm wide is firmly attached to the railing of a ship by clamps so that the rest of the board extends 2.00 m horizontally over the sea below. A man of mass 80.0 kg is forced to stand on the very end. If the end of the board drops by 5.00 cm because of the man’s weight, find the shear modulus of the wood.

SEE MORE QUESTIONS