A beam with a solid homogeneous rectangular section is simply supported at A and B.A concentrated load F= 150 kilonewtons (kN) acts at point C where distance L1 (A to C) =2.50 metres (m) and distance L2 (C to B)= 1.65 metres (m). The dimensions of therectangular section of the beam are breadth, b = 35 mm and depthd = 125 mm.Calculate the second moment of area for rectangular section of the beam about itscentroidal x-axis (Ixxcentroid). Give your answer in mm4 and rounded to nearest mm4.9000

Given B = 35 mm D = 125 mm Moment of inertia of rectangle = bd3/12 Hence required solution is…

beam with a solid homogeneous rectangular section is simply supported at A and B. concentrated load F= 150 kilonewtons (kN) acts at point C where distance L1 (A to C) = .50 metres (m) and distance L2 (C to B)= 1.65 metres (m). The dimensions of the ectangular section of the beam are breadth, b= 35 mm and depth d = 125 mm. alculate the second moment of area for rectangular section of the beam about its entroidal x-axis (Ixxcentroid). Give your answer in mm4 and rounded to nearest mm4.

beam with a solid homogeneous rectangular section is simply supported at A and B. concentrated load F= 150 kilonewtons (kN) acts at point C where distance L1 (A to C) = .50 metres (m) and distance L2 (C to B)= 1.65 metres (m). The dimensions of the ectangular section of the beam are breadth, b= 35 mm and depth d = 125 mm. alculate the second moment of area for rectangular section of the beam about its entroidal x-axis (Ixxcentroid). Give your answer in mm4 and rounded to nearest mm4.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A uniform brass plate with area of 18 x 18 m?, has mass of 3 kg which is hold by three cables in the horizontal position as shown. Please calculate the tension in each cable. B A 6 m. 9 m. 12 m. 9 m. ANSWERS TA (N) TB (N) Tc (N)
Calculate the weight (lbs) of a solid steel roller bar. It is 14.0 in. long and 3.0 in. in diameter. Use the density of steel ≈ 0.2833 lb/cu in. (Round to the nearest hundredth.)?
A shearing force of 75 N is applied to an aluminum rod with a length of 10 m, a cross-sectional area of 1.0 x 10-5 m2, and a shear modulus of 25 x 109 N/m2. As a result the rod is sheared through a distance in mm of:
A block of copper has surface area, A=10cm2 effected by its upper and lower surfaces by an opposite forces (F=50N) which cause a shearing stress, Calculate the shearing angle, under that shearing forces .
The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s = 300, in units of 106 N/m². What are (a) the Young's modulus and (b) the approximate yield strength for this material? Assume & = 0.0010. (a) Number (b) Number 1.5E11 Hint 3E8 eTextbook and Media Stress (10 N/m²) E Strain Units 28 N/m^2 or Pa Units N/m^2 or Pa SUPPORT
An aluminium wire and steel of the same length & cuoss-section are joined end lo end. The composite wire is hung from a rigid suppout and a load is suspended from free end. If the increase in the composite wire és 2.4mum, find the increase in the length of each wire. is
Two wooden members, each having a width of b = 2.4 in. and a depth of d = 0.8 in., are joined by a simple glued scarf joint. Assume B = 47°. If the allowable shear stress for the glue used in the joint is 94 psi, what is the largest axial load P that may be applied? Answer: P = i ! Ib
Structural member AB is to be supported by a strut CD. Determine the smallest length CD may have, and specify where D must be located for a strut of this length to be used. Take x= 120 mm. 60 mm D. y 20 mm E The smallest length CD may have is mm. The coordinates of point Dare ( and Imm.
Suppose a person’s femoral diaphysis is idealized as a solid circular cylinder with a diameter of 2 cm. The ultimate stress in tension is 120×106 pa. Calculate the maximal tension force the femoral diaphysis can sustain.
A 180-kg load is hung on a wire of length of 4.50 m, cross-sectional area 2.000 x 10-5 m2, and Young's modulus 8.00 x 1010 N/m2. What is its increase in length (mm)?
The total cross-sectional area of the load-bearing calcified portion of the two forearm bones (radius and ulna) is approximately 2.3 cm2. During a car crash, the forearm is slammed against the dashboard. The arm comes to rest from an initial speed of 80 km/h in 5.1 ms. If the arm has an effective mass of 3.0 kg, what is the compressional stress that the arm withstands during the crash? Pa
One end of a steel rod of radius R = 10mm and length L = 90 cm is held in a vise. A force of magnitude F = 50000 N is then applied perpendicularly to the end face (uniformly across the area) at the other end, pulling directly away from the vise. What will be the elongation of the rod (in the unit meters)? Young modulus is 200 × 109 N/m2)