Answered: Two solid cylindrical rods support a… | bartleby

Related questions

Question

Two solid cylindrical rods support a load of P = 31 kN as shown. Determine the axial load in rod (1).
5.6 m
3.8 m
25.20 KN
O 32.11 kN
O 35.17 kN
29.14 KN
O 23.72 kN
(1)
B
4.6 m
C
3.3 m

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

The following container is spun with an angular velocity of 12 rad/s after being 45% filled with water. Determine the pressure that would be at the base of the container at the most outer diameter if it has a diameter of 250mm, a height of 200mm and the container is sealed. Ø250mm Ø200mm P= ?
A weed trimmer for yard work has a rotating head which consists of a spool of monofilament line, with a strand of line that extends out from the edge. The spool has an inner diameter of 3.00 cm and an outer diameter of 18.0 cm, and a mass of 100 g. The strand has a length of 16.0 cm. The monofilament line has a linear density of 10.0 g/m. 16.0 cm- Need Help? 3.00 cm (a) When switched on, the trimmer speeds up from 0 to 2.500 rev/min in 0.225 s. What average power (in W) is delivered to the head by the trimmer motor while it is accelerating? (Round your answer to at least one decimal place.) -18.0 cm- (b) When the trimmer is cutting weeds, it spins at 2,100 rev/min and the weeds exert an average tangential force of 9.15 N on the outer end of the line, which is still at a radial distance of 16.0 cm from the outer edge of the spool. What is the power (in W) delivered to the head under load? W Read
When a certain liquid freezes, it expands about 10.0%. What would be the pressure increase inside an engine block if the liquid in it froze? (The bulk modulus of the liquid when it solidifies is 1.60 x 10° N/m².) N/m2 Need Help? Read It
Calculate the weight (lbs) of a solid steel roller bar. It is 14.0 in. long and 3.0 in. in diameter. Use the density of steel ≈ 0.2833 lb/cu in. (Round to the nearest hundredth.)?
A 25-ft crane supported at its lower end by a pin is elevated by a horizontal cable. A 250-lb load is suspended through the cable. The center of gravity of the crane is 10 ft from the pin, and the crane weighs 200 lb. Hint: You don't have to convert the unit since they cancel out on both sides. 25. Find the tension in the cable. T $25016 26. Find the total force acting on the pin. y 27. Find the direction of the force acting on the pin, o = ? 60⁰° W(2001b)
Two builders carry a sheet of drywall up a ramp. Assume that W = 2.10 m, L = 3.20 m, 0 = 25.0°, and that the lead builder carries a (vertical) weight of 187.0 N (42.0 lb). What is the (vertical) weight carried by the builder at the rear? The builder at the rear gets tired and suggest that the drywall should be held by its narrow side. What is the weight (in N) he must now carry?
Two circular platforms are attached to a fluid reservoir. On one platform rests the entire cast of Glee frozen in carbonite. A force of 7.0 N is applied downward to the empty platform with radius 8.0 m. The other platform applies a force of 7.2 N to the carbonite-frozen pop-idols. What is the radius of the platform holding the Glee cast?
After an unfortunate accident occurred at a local warehouse, you were contracted to determine the cause. A jib crane collapsed and injured a worker. An image of this type of crane is shown in the figure.The horizontal steel beam had a mass of h 80.00 kg per meter of length, and the tension in the cable was T = 12170 N. The crane was rated for a maximum load of d 500 kg. If d 5.580 m, s = 0.522 m, x = 1.850 m, and h = 1.890 m, what was the magnitude of WL (the load on the crane) before the collapse? The acceleration due to gravity is g = 9.810 m/s². WL WL = N What was the magnitude of force Fp at the attachment point P? Fp N