8. An underground storage tank for gasoline is in the shape of a cylinder on its side. It has length15 feet and radius 3 feet. It is buried so that the distance from the çenterline of the tank toground level is 7 feet. See the diagram below for what the tank looks at when viewed on end. Itis filled with gasoline that has a weight density of 45 lbs/ft3. Determine the work required topump all the gasoline out of the tank.35W.Ground Level7 ft. (3) :לןז'א1 -3 ft

Answered: Image /qna-images/answer/1133ee2d-8ea7-400e-a9d1-d61d3d94b75e.jpg

Answered: An underground storage tank for…

Similar questions

A tank is shaped like an inverted cone, is a quarter full of water, and has a radius of 6 meters and a height of 30 meters. Find work needed to pump the water from the tank. Use density of water 1000 kg/m^3 and g=9.8 m/s.
A log splitter uses a pump with hydraulic oil to push a piston, attached to which is a chisel. The pump can generate a pressure of 2.4x107 Pa in the hydraulic oil, and the piston has a radius of 0.035 m. In a stroke lasting 15 s, the piston moves 0.69 m. What is the power needed to operate the log splitter's pump? Number i Units
A tank is full of water. Find the work W required to pump the water out of the spout. (Use 9.8 m/s² for g. Use 1000 kg/m³ as the weight density of water.) |--4m+ W = 3 m † 4 m ↓ 9 m
When gasoline is burned in the cylinder of an engine, it creates a high pressure that pushes on the piston. If the pressure is 150 pound-force per square inch [psi], and it moves the 4-inch [in] diameter piston a distance of 4 centimeters [cm] in 0.2 seconds [s], how much horsepower [hp] does this action produce? Click the icon to view the conversion table. Click the icon to view the table of common derived units in the SI system. ..... The power is 0.01 hp. (Round your answer to two decimal places.)
A tank has the shape of an inverted circular cone with height 7 m and base radius 3 m. It filled w water. Set up the integral form, don't evaluate it, for the work required to empty the tank by pumping all of the water to the top of a tank. (The density of water is 1000 kg/m³ and the acceleration due to gravity is 9.8 m/s²). 9800 7 S 9800 9800 49 9 - 49 * (7 — x)² dx 9 (7-2)²dx 49 (7 — x)² dx 7 9 [²3/10 S 49 -(7 — x)³ dx 7 9 √2/2 49 -(7 — x)² dx
An automobile tire is shown in the figure below. The tire is made of rubber with a uniform density of 1.10 x 10 ka/m, The tire can be modeled as consisting of two flat sidewals and a tread region. Each of the sidewalls has an inner radius of 16.5 cm and an outer radius of 30.5 cm as shown, and a uniform thickness of 0.05 cm. The tread region can be approximated as having a uniform thickness of 2.50 cm (that is, its inner radius is 30.5 cm and outer radius is 33.0 cm as shown) and a width of 16.0 cm. what is the moment of inertia (in kg -m) of the tire about an axis perpendicular to the page through its center? Sidewall 33.0 cm 16.5 cm 50.5 cm Tread kg- m2
With all steps please
Please don't provide handwritten solution .....
A trough full of water is 20ft. long and its cross section is in the shape of an isosceles triangle 4ft. wide across the topand 4ft. deep. How much is the work done in pumping all the water out of the trough over the top?
An aquarium 11m long, 2m wide, and 9m deep is full of water. The density of water is 1000kg/m3 and the force of gravity is 9.8m/s2 a) Find the work needed to pump all of the water out of the aquarium b) Find the work needed to pump half of the water out of the aquarium.
Assume that a raindrop has a volume of 0.05 cm^3 and you need an Avogadro's number of raindrops to fill up the cubic water tank. What is the length of the edge of the tank?
6.2

SEE MORE QUESTIONS