B- Define hydration. What must you do to make sure that hydration process is going well (As a site engineer)? C- Differentiate briefly between central, shrink and truck concrete mixing methods. D- What is the importance of vibrator and what is the bad effect of putting vibrator in concrete for long time (more than 15 seconds)?

B- Define hydration. What must you do to make sure that hydration process is going well (As a site engineer)? C- Differentiate briefly between central, shrink and truck concrete mixing methods. D- What is the importance of vibrator and what is the bad effect of putting vibrator in concrete for long time (more than 15 seconds)?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the Early Start (ES) and Early Finish (EF) of activities in a precedence diagram methods (PDM) network diagram based on the Table 1 below. Table 1: List of activities, predecessor and duration Activity Predecessor Duration A В A C A D В E 3 F D, E 4 LO 4.
10. If there is a river on the road construction site, how to solve the problem? * Your answer
Q2: For the project, its data shown below find: ● Time in weeks that gives a probability of %97.5 Probability of finishing the project 4 weeks more than TE Probability of finishing the project 3 weeks less than TE Act. 1-2 2-3 2-5 2-4 3-4 3-7 5-6 6-7 4-7 0 8 4 7 7 4 7 10 10 4 M 10 5 9 6 8 14 14 5 P 24 12 21 11 8 15 24 24 12
Using the activity list below and any appropriate drawing tool, create a complete network diagram using the precedence method showing Activity, Duration, ES, EF, LS, LF and Slack per activity: ACTIVITY A B C D E F G H DURATION 5 12 20 15 15 30 12 8 PREDECESSOR A B B B C, D E, F G
The project schedule is shown below. Illustrate and do the Forward & Backward pass and answer the ff: ACTIVITY PPREDECESSOR DURATION (days) A 5 B A 8 B B C D E F U D, E G F How many days is the project's duration? Select the correct response. 33days 29days 25days None of the choices 63 72 1
). The network and durations given below show the normal schedule for a project, and the table given below summarizes the time-cost information for the activities, the owner wants to finish the project in 110 days, so find the minimum possible cost for the project to finish in 110 days AND 20 A B C D (19) E F 9. Activity (days) 120 20 40 30 50 60 Normal du 120 60 Crash (days) 100 15 30 20 40 45 30 on 4 50 Norma Cost 12000 1800 16000 1400 3600 13500 Cost 14000 2800 22000 2000 4800 18000
Question 4: Determine the amount of time in weeks that gives a probability of 97.5% until the seventh event in the following grid, and then find the following: What is the probability of completing the project with a period less than TE by 4 weeks What is the probability of completing the project with a period of more than TE by 2 weeks Act. 1-2 2-3 2-5 2-4 3-4 3-7 5-6 6-7 4-7 0 8 4 7 7 4 7 10 10 4 M 10 5 8 9 6 8 14 14 5 24 12 21 11 8 15 24 24 12
4. Introduction section in the proposal consists of the followings: a) Statement of the problem b) Data collection c) Conclusions d) Recommendations 5. Which of the following best describes quantitative research? a) The collection of non-numerical data b) An attempt to confirm the researcher's hypotheses c) Research that is exploratory d) Research that attempts to generate a new theory
1-2 1-3 2-4 3-5 4-6 4-9 5-6 5-7 6-8 7-8 8-10 9-10 10-11 Activity 6 4 4 5 1 2 2 M 4 8 7 3 7 3 4 4 15 8 10 12 9 11 4 5 For the project detailed find the probability of completing the project within a period of 33 weeks? PM 4:52 Js
The figure shows a beam made from a material having an allowable tensile stress of 135 MPa and a compressive stress of 165 MPa. The couple M is applied to the beam in a plane forming an angle of 45° as shown in the figure. a) Determine the location of the centroid of the cross section b) Calculate the moments of inertia about the principal axes, I, and ly c) Determine the maximum allowable internal moment M that can be applied to the beam N M Y 140 mm 140 mm 45⁰ 140 mm 280 mm 140 mm 140 mm
Complete Answer
I need the answer as soon as possible