se study. The report should cover the following ints: Most common estimation tools available in the rket. Students also need to investigate the mo mmon software used by Quantity Surveying ms. Students should select any case study or proje

Q: 3. A car has an initial speed of 25 m/s and a constant deceleration of 3 m/s^2. Determine the…

A: Using equations:v-u=atv2-u2=2ass=ut+12at2

Q: An earth dam require a total of 150 cubic meter of soll compacted with a bulk unit weight of 18.5 kN…

A:

Q: A bridge is to be built across a rectangular channel carrying flow of 200 m/s at certain depth. The…

A: Solution Bridge is to be constructed across a rectangular channel. Depth of water and width of the…

Q: I. Determine the rotation at point A and the deflection at the free end using moment diagram by…

A:

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

A: Given data in question  Load 3350 N Angle 46° a= 1.9 m To find out  Forces in each member

Q: A conical draft-tube having diameter at the top as 2.0 m and pressure head at 7 m of water (vacuum),…

A:

Q: A 50 dm diameter well gives a discharge of 0.05 m³/sec. Two observations well were made at a…

A: Given data,  q = 0.05 m³/s B = 10 m Diameter of well = 5 meter

Q: The uniform beam has a mass of 48 kg per meter of length. Determine the reactions at the supports. A…

A: Given Data  Uniform beam has a mass of 48 kg/m  Find the support reaction in terms of Netwon(N).

Q: Liquid is flowing in a pipeline 60 mm in diameter at 9.5 cu. m. per hour. If the density of fluid is…

A:

Q: 6. Determine the resultant moment about point A of the system of forces shown below. Each square is…

A:

Q: QUESTION 1 An element in plane stress is subjected to stresses; Ox, Oy, and Txy (FIGURE 1). Using…

A: NOTE - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: The hydraulic conductivity, k of a soil is 7.15 x10-°cm/s at a temperature of 20° C. Determine its…

A:

Q: Determine the forces in the members by using the method of section and inspection. 120 AN 120 AN 120…

A: The method of sections is generally a process helped to determine the unknown forces acting on…

Q: 4. Determine the distance 'a' as a fraction of the beam's length 'L' for locating the roller support…

A: Given moment at B should be zero. I have considered the moment at B from right end side .

Q: A steel [E = 200 GPa ] rod with a circular cross section is 20 m long. Determine the minimum…

A:

Q: 1. From the given cross section of the proposed barangay road. The road base is 6m and the side…

A: Consider the given data.

Q: Determine the moment of inertia with respect to the horizontal centroid of the figure. 250 38 300 25…

A: A section have been given and it has been asked to determine moment of inertia about horizontal…

Q: A pump with 400 mm diameter suction and a 350 mm diameter discharge pipe is to deliver 20,000 liters…

A:

Q: The rectangular channel has a width of 8 ft and transports water at 18(103) ft³ /min. Suppose that…

A: Given :Width (B) = 8 ftDischarge (Q) = 18×103 ft3/min= 18×10360 = 300 ft3/secDepth at section 1 (y1)…

Q: The force F has a magnitude of 710 N. Express F as a vector in terms of the unit vectors i and j.…

A:

Q: The cylindrical pressure vessel with hemispherical end-caps is made of steel. The vessel has a…

A: Longitudinal Stress is the vessel has closed ends the internal pressure acts on them to develop a…

Q: A survey of a closed traverse ABC shows the following latitudes and departures: Line AB latitude…

A:

Q: Determine the ultimate moment capacity of a reinforced concrete T-beam with the following…

A:

Q: Which property is a better measure of the productivity of an aquifer: porosity or hydraulic…

A: Porosity and hydraulic conductivity are two important properties of an aquifer that determine its…

Q: SITUATION 4. For Items 10-11. | 60 kN 40 kN/m 120 kN • m |E im---1m-| 10. Find the maximum shear…

A:

Q: 4. A mass m is on a frictionless incline that makes an angle 0 with the horizontal. Let m = 25.0 kg…

A: solution: m=25kg  theta = 300

Q: Use the virtual work method to determine the slope and deflection at point D of the beam shown. -15…

A:

Q: Material Strengths: Fy = 248 MPa, Fu= 400 MPa The channel (C200X17.1) is connected with four M16…

A:

Q: 2. USE CONJUGATE BEAM METHOD. For the beam shown, determine the following: a. Slope at point A in…

A:

Q: 5. A car starts from rest and moves with a constant acceleration of 1 .5 m/s^2 until it achieves a…

A:

Q: Determine the Deflection at the midspan of AB in inches unit. Use the Double Integration Method.…

A: This method entails obtaining the deflection of a beam by integrating the differential equation of…

Q: A soil sample having a void ratio of 1.3, water content of 50% and a specific gravity of 2.60, is in…

A:

Q: 2. Use the virtual work method to determine the horizontal deflections at joint C of the frame…

A:

Q: A city has a population of 50000 people and they consume an average 20 million m3 of natural gas per…

A: Question is based on the solid waste management data.Population of city,average consumption of…

Q: 5. Three balls are stacked in a container as shown. If each ball weighs 25 kg, determine the normal…

A:

Quantity takeoff

Quantity takeoffs (QTO) are precise estimates of the materials and labor costs required to finish a construction project. During the pre-construction phase, an estimator prepares them, breaking down the project into smaller, more manageable parts that are easier to evaluate. These measurements are used to prepare a construction scope bid. Estimators examine the drawings, specifications, and models to figure out different quantities and their costs. Since, the components, their quantity, and price are all included in the model, quantity take-off can be done automatically using Building Information Modelling (BIM). The time taken for completing a construction project can be reduced by the use of quantity takeoff. These takeoffs are also called material takeoffs and construction takeoffs.