b) Air at 30°C flows through a 70 m long, 2 cm x 2 cm rectangular cross section pipe as shown in Figure 1(b). The flow is laminar flow and centerline velocity is 2 m/s. If the angle of pipe measure from horizontal plane is 35°, determine : (i) Reynold number; (ii) pressure different; (iii) head loss; (iy) wall shear stress:

b) Air at 30°C flows through a 70 m long, 2 cm x 2 cm rectangular cross section pipe as shown in Figure 1(b). The flow is laminar flow and centerline velocity is 2 m/s. If the angle of pipe measure from horizontal plane is 35°, determine : (i) Reynold number; (ii) pressure different; (iii) head loss; (iy) wall shear stress:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the conditions shown in schematic 1m figure, find the force F required to lift the Absolute pressure 10 kPa abs. 1m trapezoidal sectional concert gate with Water 20°C 1m length on paper. The concrete gate 3m weighs 7.5 kN and the atmospheric Glycerin Sg 1.2 A D pressure is 100 kPa. 0.4m B 0.6m
Determine the shear flow distribution in the thin-walled L-shaped section shown. Two shear forces Vy and V₂ are applied through the shear center of the section and thickness of all panels are equal to t. Vy h/2 2 3 V₂ h 1
c. Derive the expression for the friction factor, f = 64/Re under laminar flow conditions
Repeat Problem 8.12 if the pipe is on a 20° hill. Is the flow up or down the hill? Explain. Problem 8.12 The pressure drop needed to force water through a horizontal 1-in.-diameter pipe is 0.60 psi for every 12-ft length of pipe. Determine the shear stress on the pipe wall. Determine the shear stress at distances 0.3 and 0.5 in. away from the pipe wall. >
complete the table also
See the sketch below from our textbook. The positive x-direction is to the right. The bottom wall is fixed, and the top wall is moving in the positive x-direction. Assume the velocity profile is u(y) = (8y-0.3 y²), y is mm. Also assume that the liquid sec N-sec (not water) is non-Newtonian, such that the viscosity = 0.482 m² of the bottom and top walls is 5 m² each, what shear forces does the liquid apply to the lower and upper walls? 4 mm u F If the area P
A. Determine the magnitude and direction of the hydrostatic force acting on the gate using the PRESSURE PRISM CONCEPT. Illustrate and label the pressure diagram/prism as part of your solution. Express your answer in kips. B. Determine the magnitude and direction of the force exerted on the plate by the ridge. Illustrate and label the FBD of the force system. Express your answer in kips.
the pipe? [-2. A steel pipeline with a nominal diameter of 24 in has an ID of 22.624 in (575 mm) and a wall thickness of 0.688 in (17.5 mm) carries a flow of 28 ft3/s (794 L/s). The pipe makes a short-radius 90° turn. What is the force developed in a buttress at the bend? What stress would be developed in the pipe by this change in direction if no buttress were provided? -3. What is the maximum stress which could be produced in the pipe of Prob. 6-2 as a result of suddenly closing a valve in the line? (K for water is approximately 10 percent of the value of E for steel.) SoLve Prob (6-3) REFERENCES 1. John Parmokie
Water enters and leaves a T-shaped piece of pipe located in the horizontal plane. (1) the relative pressure in the numbered section is 200 kPa and the cross-sectional average velocity is V1= 2 m/s. since the pipe diameters are the same in sections (2) and (3), determine the components of the force acting on the pipe. It will be assumed that there is no energy loss in the selected control volume.
Pls hand written solution
i need the answer quickly
1. A semi-circular gate of diameter "d" and radius "r" is submerged in a liquid and has its diameter on the liquid surface. a. Compute for the value of eccentricity if the top of the gate is 2m from the surface and radius is 2 m. b. Compute the location of the center of pressure if the top of the gate is 2m from the surface and radius is 2 m. c. Compute for the hydrostatic force on one side 4r 13n hg CG. CP.