X oil s = 0.80 h water 3m -3m

Q: Determine the pressure at the center of the pipe from the piezometer shown. 200mm WATER 75mmØPIPE

A: Given:- a piezo meter is attached to the pipe as shosn below

Q: Q.4 A non-Newtonian fluid is flowing in a floor having height 5mm and with a free stream velocity of…

A: Given data- Non-Newtonian fluid- height h=5 mm, Free stream velocity=0.5 m/s, Yield stress=38 MPa,…

Q: horizontal pipe, which of the following is constant? Pressure head Elevation head Velovity head

A: In horizontal pipe, pressure head, elevation head and velocity head all will be constant { however…

Q: The diameter of a pipe carrying oil (s=0.92) changes gradually from 400 mm at A to 600 mm at B.…

A: To Determine (a) The direction of flow; (b) the frictional loss between the two points.

Q: A glass of water is filled to a height of 0.5 ft. Find the hydrostatic pressure at the bottom of the…

A: Hello dear this is the solution of your problem The answer is found to be Pressure at the bottom of…

Q: t (s) for 10L t (s) for 10L t (s) for 10L 51.65 V L/s O. 196 h2 mm h3 mm h4 mm h5 mm h6 mm h1 mm 240…

A:

Q: Compute the magnitude and direction of the resultant acting on the roller. 9N 30N/m 1m 4m 2m 100N/m…

A:

Q: 8.8 The spherical gas tank is made of steel (E = 29 × 106 psi, v = 0.3). The inner radius of the…

A: Data is as given

Q: Determine the magnitude and direction of the hydrostatic force acting on the gate using PRESSURE…

A: Hydrostatic forces on surfaces deals with the fluids i.e., liquids and gases at rest. The velocity…

Q: The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. If the valve A is…

A: Given:- Inner diameter of pipe, di=12 inWall thickness, t=0.25 inWater pressure inside pipe, P=300…

Q: The fluid in the tank is water. Flow is steady state, incompressible and nonviscid. It is known that…

A: Using the Bernoulli's equation between the tank and the point 1 -  Patmρg + v122g + Z1 = P1ρg +…

Q: derive an expression for pressure at Summit of siphon.

A: Siphon- It is a long bent pipe which is used to carry water from a reservoir at a higher elevation…

Q: Determine the resultant force of the water acting on the circular glass plate that is bolted to the…

A: Consider the figure,

Q: he diameter of a pipe changes gradually from 6 inches at A to 18 inches at B. A is 15 ft lower than…

A:

Q: The springs BA and BC each have a stiffness of500 N/m and an unstretched length of 3 m. Determinethe…

A: Given :- k= 500N/m L=6m F=175 N To find:- d

Q: Determine

A:

Q: a)Determine the difference in pressure between A and B in kPa if h = 0.15 and SG of oil is 0.862.…

A:

Q: Determine

A:

Q: diameter. 11. The maximum force exerted by a small bydraulic press is 500 kN. The working pressure…

A:

Q: Water flows steadily downward through the pipe shown in the figure below. Viscous effects are…

A: To determine the,  A) Flow rate in the pipe B) Pressure at point 2

Q: The air above the liquid (S.G.=0.85) is under a pressure of 40kPa gage. The rectangular gate is 2.0m…

A:

Q: A. Determine the stress at the bottom in the free end. (MPa) 3. Determine the stress at the top in…

A: consider 15 % loss in prestress force

Q: 6-55. Locate the center of gravity z of the assembly. The cylinder and the cone are made from…

A: Draw the free-body diagram of the given figure. For the segments Center of Mass are tabulated as…

Q: air 6.tom 0.40m 0.S0m C. eil (s=0.50) gaseline (s= 1.60)

A: Finding out pressure at A.

Q: A homogeneous rectangular gate AB 6.1 ft wide and 10 ft long. Friction in the hinge is negligible.…

A: To find force on surface AB

Q: If the pressure head in pipe A is 2 m of water, determine the pressure in pipe B. ‚OIL of Sp. gr.…

A: Given: Pressure head in A = 2 m of water Specific gravity of oil = 0.8

Q: 0.3m B Water 0.4m Oil RD=0.8 0.2m 0.4m Water 0.4m

A: Note :- as diagram can be read from the question itself so not drawing in answer as no changes is…

Q: Water flows in a steel pipe (ɛ = 0.00020 feet) at a flow Q = 12.5 cfs. The diameter of the pipe is…

A: Given that:                Flow, Q=12.5 cfsDiameter of pipe, D=18 inLength of pipe, L=2500…

Q: find passive and active pressure

A: Draw the given profile:-

Q: Determine in psi the pressure drop between the ends of this duct.

A: Given data: P1=0.0406 lb/in2. P2=0.022 lb/in2.

Pressure and Stress