Determine the gage pressure at the center of the pipe (point A) in pounds per square inch when the temperature is 70°F with h, = 16 in. and h, = 2 in. Pipe (section view) Water Mercury

Q: Find the difference in (KN/m²)

A: take density of air is 1.225kg/m3 water is 1000 kg/m3

Q: Please be clear with your soltuion. In the figure, x=25cm initially. If the pressure at m is…

A:

Q: Show complete and clear solution. Don't round off initial values, round off final ans only pls

A:

Q: 4.) A 150mm LONG BRONZE TUBE, CLOSED AT ITS END IS Diameter, D = 80 mm Thickness, t = 3 mm 8 0mm IN…

A:

Q: Determine the pressure difference (in kPa and answer should be a whole number) between the water…

A:

Q: For the hydraulic system shown below. 1- Determine the resistance and discharge of each pipe. CLO1,…

A: Given, PA=100 KPa Head=PA9.81=10.19 m Net head =10.19+40=50.19 m Let head loss in pipe 1 =△h1 Head…

Q: 56 1. Find the air pressure in the tank (in psi), given the following conditions 0.9 AIR 6세

A: Given :

Q: 1. Find the air pressure in the tank (in psi), given the following conditions. SG =0.9 AIR LA *0,51…

A:

Q: As shown in the figure below, the smaller pipe is cut off a short distance past the reducer so that…

A:

Q: In fi. If h1= 1 m, h2=. 0.5 m. what is the pressure at. A ?(. SG1= 0.7, S.G2= 0.8) s.g.1 h2

A:

Q: 2 1 5. v=R3S2 n hf 10.29n²LQ² D16/3

A:

Q: From the figure shown. Find the pressure head and the pressure at A when fluid A is water, Fluid B…

A:

Q: Q2: An oil of Viscosity Co.15 pa.s) and specific gravity 0.9 is flows Throngh an inclined (300mm)…

A: The slope for constant pressure throughout the pipe is given by: sinθ=-32μVγD2 Where, V = Velocity…

Q: Q1: Find the equivalent pipe for the loop shown below, also find the pressure at point C if the…

A: Given, Q=252 m3/hr=0.07 m3/sec Pressure at Point A=450 Kpa CHW=100 PIPE AB BC AC DIAMETER 200…

Q: Q2: Find the diameter of the pipe 2 in the loop shown below which contains two pipes connected in…

A: ##Calculation of diameter of Pipe 2 using hazen Williams equation

Q: Steel tube shaft having length 3mm and diameter 50mm subjected to axial compressive force 55 k N and…

A:

Q: In the figure shown, determine the height h of water and the gage reading at A when the absolute…

A:

Q: 8.8 The spherical gas tank is made of steel (E = 29 × 106 psi, v = 0.3). The inner radius of the…

A: Data is as given

Q: 16. Calculate the pressure, in kPa, at A, B, C, and D.

A:

Q: Determine the minimum thickness of the tank plating if the internal pressure is 1.3MPa and the…

A: Internal pressure=1.3MPa Allowable stress= 38MPa To find minimum thickness of tank

Q: In a 200 foot tall water tank, the pressure at the bottom is a. 1960 kPa b. 86 psi c. 25 psi d. 500…

A: Introduction : In this question we are provided with value of depth of water in water tank in term…

Q: Calculate the X length that can keep the gate closed. The gate is hinged from point A. The pressure…

A:

Q: Hollow shaft AB (4" outside diameter, 3.5" inside diameter) is made of aluminum (E=10x106 psi,…

A:

Q: QI: Find the equivalent pipe for the loop shown below, also find the pressure at point C if the…

A:

Q: Find the pressure in the pipe.

A:

Q: A cylindrical pressure vessel with a diameter of 600 mm is to be fabricated from steel plates of…

A:

Q: The diameter of the tube is 3.446mm. The surface tension of water at 20°C is equal to 0.070. For a…

A:

Q: A non-homogenous rectangular bar as shown in the figure thickness of ½ in. Determine has a constant…

A:

Q: For the figure shown, calculate the elevation of the pressure head at the junction (P). Round off…

A: The given data is: Elevation at A=50 m D1=1200 mm=1.2 m L1=1800 m Q1=1.35 m3/s f=0.02

Q: A. Calculate for the axial force in kN at member GK using cantilever method. Enter absolute value…

A: Solve using cantilever method: Assumption: The Point of contraflexure in all member lie at its…

Q: 8

A: For spherical gas tank, both hoop stress and longitudinal stress is same  σL = σh = pd/4t d= 6.5 m…

Q: A vertical triangular gate with Alcohol (SG = 0.78) on one side is shown in the figure. Determine…

A: The values and diagram given in the question are as follows: Specific gravity of alcohol(Sg)=0.78

Q: Find flow velocity and flow rate in pipe a and b using Equivalent pipe length method and hazen…

A: Given, Pipe network diagram with various components    To find : flow rate in pipe a and b

Q: Elev 7m Elev 6m Elev 3m Elev 1m Elev Om Air Pressure 35 kPa Oil Sp. Gr. 0.82 Water Mercury kay

A: Given data  Air pressure (Pa) = 35 KPa = 35 × 103 N/m2  Specific gravity of oil (Go) = 0.82  Assume…

Q: Find the thickness of hollow cylinder

A: Introduction : The given question is related with solid mechanics . In this question we have to…

Q: 11. The tank in the adjoining figure contains oil of specific gravity of 0.75. Determine the reading…

A: Given data in question  Specific gravity 0.7 Depth 3 m and 22 cm Air To find out  Reading at A

Q: Reg.no : 5393   Pb # 3: Refer to Figure 2. Assume that friction is negligible, that θ = 115o, and…

A: Given figure:

Q: 450-mm diameter 0.45 m 15 m Circular view port is centered in inclined side of Oil tank. (sg -0.85)…

A: By subtracting the magnitude of the smaller force from that of the larger force, we get the…

Q: The figure below shows a fabricated assembly made from three different sizes of standard steel…

A:

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?