The air above the liquid (S.G.=0.85) is under a pressure of 40kPa gage. The rectangular gate is 2.0m wide.a) Determine the hydrostatic force acting on the gate.b) Determine the location of the force measured from the hinge.c) Calculate the minimum value of P to hold the gate in place. The air above the liquid (S.G.=0.85) is under a pressure of 40kPa gage. The rectangular gate is 2.0m wide.a) Determine the hydrostatic force acting on the gate.b) Determine the location of the force measured from the hinge.c) Calculate the minimum value of P to hold the gate in place.AirO 40 kPaY1 =1m.Hingey2 =3m

Answered: Image /qna-images/answer/c74190f1-56d0-461f-aee4-058137598c81.jpg

The air above the liquid (S.G.=0.85) is under a pressure of 40kPa gage. The rectangular gate is 2.0m wide. a) Determine the hydrostatic force acting on the gate. b) Determine the location of the force measured from the hinge. c) Calculate the minimum value of P to hold the gate in place. Air O 40 kPa Y1 =1m. Hinge y2 =3m

The air above the liquid (S.G.=0.85) is under a pressure of 40kPa gage. The rectangular gate is 2.0m wide. a) Determine the hydrostatic force acting on the gate. b) Determine the location of the force measured from the hinge. c) Calculate the minimum value of P to hold the gate in place. Air O 40 kPa Y1 =1m. Hinge y2 =3m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported rectangular aluminium plate has a length a = 5.0 m; and a width b = 2.0 m. It is designed to carry a lateral pressure of 6 MPa. Take E = 120 GPa, v= 0.27, oy = 280MPa and p=2700kg/m³ Determine The minimum required thickness h of the plate(consider the factor of safety n = 1.5); The fundamental frequency of the plate.
A) Bar AB is 60mm x 10 mm thick, E = 65 GPa, a1 = 9.5 x 10-6/°C. B) Bar BC is 20mm in diameter, E = 170 GPa, a2 = 7.5 x 10-6/°C.
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If the normal stress in each rod must be limited to 280 MPa, determine the minimum diameter d₂ required for rod (2). 80 KN d₁ O 18.2 mm O 28.7 mm O 24.6 mm O 30.2 mm O 21.7 mm 140 KN 140 KN B (2)
The elliptical pipe carrying steam at 3.5 mPa has an outer major axis length of 500 mm and an outer minor axis length of 400 mm with a wall thickness of 10 mm. A gasket is inserted between the flange at end of the pipe , and a flat plate is attached using 40 mm diameter bolts to cap the end . The allowable Stress in the bolts is 80 Mpa. How many bolts must be used to hold the cap if there is an initial stress of 30 mPa ?
Solution plz
P8-1. Determine the friction force at the surface of contact. 500 N 3 W = 200 N plus 0.3 Mk = 0.2 100 N (a) (b) Prob. P8-1 W = 40 N μ = 0.9 Mk = 0.6 P P
The two cylindrical rod segments shown in the figure below (Eigure 1) are fixed to the rigid walls such that there is a gap of 0.01 in between them when T₁ = 80°F. Each rod has a diameter of 1.7 in. Take cal = 13(10-6)/°F. Eal = 10(10³) ksi, (y)al = 40 ksi, acu = 9.4(10-)/°F. (ay)eu = 50 ksi, and Ecu = 15(10³) ksi. Figure 0.01 in. Copper 12 in Aluminum 6 in. 1 of 1 What larger temperature T₂ is required in order to just close the gap? Express your answer to three significant figures. T₂ = 132 °F Previous Answers Correct Part B Determine the magnitude of the average normal stress in each rod if 7₂= 250°F. Express your answer to three significant figures and include appropriate units. - 2.78 HA ksi Submit Previous Answers Request Answer ? * Incorrect; Try Again; 3 attempts remaining
Determine the resultant force of the water acting on the circular glass plate that Is to the side panel of the tank. Also, determine the location of the center of pressure along this inclined side, measured from the top. Question 2: FYw.h.A ate Fv= Yw.V 3 m radie 9810 Ixr x gate 9810 1 m 2 m Ma:0 Nar3- Fn 号×3-fvx3- -0 Ma=0-) NBx3- F t /2Fy-0 120° 3 m 1,- I,
From the frame loaded as shown. Solve the following Find: Reaction at column BMoment at column B