A) Bar AB is 60mm x 10 mm thick, E = 65 GPa, a1 = 9.5 x 10-6/°C. B) Bar BC is 20mm in diameter, E = 170 GPa, a2 = 7.5 x 10-6/°C. (1)(2)AВC0.45 m1.30 mThe assembly above starts out at 52 degrees celsius. What is the final position of Cafter a load of P = 15 kN is applied and the temperature is cooled to a finaltemperature of 20 degrees celsius? Enter distance C moves in mm inte D2branowerbox- In Pdf, be clear if it moves to the right or the left. Assume the following:(1) Bar AB is 60mm x 10 mm thick, E = 65 GPa, a1 = 9.5 x 106/°c.(2) Bar BC is 20mm in diameter, E = 170 GPa, a2 = 7.5 x 106/°C.

Answered: Image /qna-images/answer/c0e203d6-aa64-4494-b3e4-ec3641c52867.jpg

Answered: Bar AB is 60mm x 10 mm thick, E = 65…

Bar AB is 60mm x 10 mm thick, E = 65 GPa, a1 = 9.5 x 10-6/°C. B) Bar BC is 20mm in diameter, E = 170 GPa, a2 = 7.5 x 10-6/°

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q2/A rigid bar the weight-80 kN is supported as shown in the Fig, compute the temperature change that will cause the stress in the steel rod to be 55 MPa. Assume the coefficients of linear expansion are 11.7 μm/(m °C) for steel and 18.9 μm/ (m-°C) for bronze. Bronze LAUM 1300 mm Steel E 83 GPa 1.5 m 320 mm² 300 GPS
U
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P = 7 kN, Determine the axial deformation of uniform bar 1 (in mm). Indicate negative sign if compression. 5P E-10 GPa + 39 E-200 GPo 3M 80mm 30 mm 30mm 80 mm 30 mm 30 mm
A HA He 1 m L 1 m
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P= 7 kN, Determine the axial deformation of uniform bar 1 (in mm). Indicate negative sign if compression. e 5P 39 E-200 GP gomm 30 mm 30 mvm 80 mm 30 mm 30 mm
Four pulleys are attached to the 50-mm-diameter aluminum shaft. If torquesare applied to the pulleys as shown in the figure, determine the angle of rotation ofpulley D relative to pulley A. Use G =28 GPa for aluminum.
Calculate the support reactions of the column element given in the figure. Determine the required edge length a to ensure to safety of the element that is made of a material with a safety stress capacity of 200 MPa and that supports the column at point A. ( AB and BC parts have the same material properties. )
G6//The light rigid bar ABCD shown in Figure is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the load P 20 KN is applied. Steel L=2m A=250mm 4m E=200Mpa Aluminum L=2m A=500mm 2m 2m E-72Mра P=20KN
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P = 7 kN, Determine the axial deformation of tapered rod 2 (in mm). Indicate negative sign if compression. 5P 3P E-10 GPa E-200 GPa 80mm 3o mm 30 mrm 80 mm 30 mm 30 m
3) The rigid horizontal bar AB is supported by three vertical rods as shown in the figure and carries the load of 110 kN. The system is stress free before the load is applied. After the load was applied, the temperature of all wires is raised by 20°C. Use a = 12x10-6/°C for steel, a = 18x10-6/°C for copper and a = 20x10-6/°C for brass. Neglecting the weight of the bar AB, determine the location of the 110 kN force in order that AB remains horizontal. copper bar: A=195mm? steel bar: brass bar: A=130mm? A=325mm? A C B 110 kN 3.00m 2.00m 1.80m _ 1.20m 1.50m
Two rods vertically connect beams AB and CD as shown in the figure. Point A is fixed supported while point D is hinged connected. If the rod on the right is heated by 10 degree Celsius, 2 m 2 m 2 m C Use E- 200 GPa, linear of coefficient expansion-11.7x 10° per degree celsius and A = 4500 mm2 Compute for the deformation of the right rod in mm. Select the correct response: 0.0234 mm 0.0842 mm 0.0468 mm
An elliptical gate covers the end of a pipe 4m in diameter. Of the gate is hinged at the top, what normal force F is required to open the gate when water is 8m deep above the top of pipe and the pipe is open to the atmosphere on the other side? Neglect the weight of the gate. Find: ħ in kPa Agate in m2 FR in kN ȳ in m I in m4 ycp in m F in kN