b) A junior network associate Ah Beng had set up multi-switched VLANS configuration as the master plan in Figure 1-2. Although Figure 1-2 has no problem. But he should have misconfigured the network due to a lack of experience. Currently, the result of his configuration is all switches can ping to each other, but the connectivity between the PCs is not up. Suggest and explain to him any THREE (3) probable causes for his further troubleshooting actions. VLAN 66 192 168.66.61/24 S1 Gigo/1 Gigo/2 VLAN 11 192 168.11.13/24 PCB VLAN 11 192 168.11.12/24 PCA Gigo/1 Fa0/11 $2 Gigo/2 Fa0/11 $3 VLAN 66 192 168.66.62/24 VLAN 66 192 168.66.63/24 Figure 1-2: A multi-switched VLANS network topology diagram

b) A junior network associate Ah Beng had set up multi-switched VLANS configuration as the master plan in Figure 1-2. Although Figure 1-2 has no problem. But he should have misconfigured the network due to a lack of experience. Currently, the result of his configuration is all switches can ping to each other, but the connectivity between the PCs is not up. Suggest and explain to him any THREE (3) probable causes for his further troubleshooting actions. VLAN 66 192 168.66.61/24 S1 Gigo/1 Gigo/2 VLAN 11 192 168.11.13/24 PCB VLAN 11 192 168.11.12/24 PCA Gigo/1 Fa0/11 $2 Gigo/2 Fa0/11 $3 VLAN 66 192 168.66.62/24 VLAN 66 192 168.66.63/24 Figure 1-2: A multi-switched VLANS network topology diagram

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Subject: Networking Question: Explain the timing diagrams of two different connection establishment mechanisms of TCP. Note: Check the image and answer according to this.
Question 2 Match the following to one or more layers of the OSI Model. a. Router determination b. Flow control c. Interface to transmission media d. Provides access for end user
PROBLEM 1: Following figure is related to IED Based Substation Automation. Describe each layer related substation Automation. Also explain the functions of each element in the layers. IED Baed Computer networks for Substation Automation HMIS Modbus TCP/IP Sub-station Operation Center Host N MODBUS RTU IED1 IED2 IED 3 IEDN Cabeling CT/VT Switch CT/VT Switch Power System Environment CT/VT Switch CT/VT Switch Lower Middle Layer Layer Upper Layer
It's important to offer a rundown of the most typical network architectures. If you had to choose, which would you say is the most reliable?
Ethernet and ATM both specify Data Link layer framing techniques. How do they differ?a. Ethernet uses CRC fields to confirm the validity of the frame, whereas ATM uses no error detection.b. Ethernet uses variably sized packets, whereas ATM uses fixed-sized cells.c. Ethernet uses synchronous transmission, whereas ATM uses asynchronous transmission.d. Ethernet uses frame headers, whereas ATM does not.e. Ethernet offers no guarantee of timely delivery, whereas ATM ensures that packets are delivered within 10 ms
17 Correct and detailed answer will be Upvoted else downvoted. Thank you!
Let's pretend a company needs a new network installed and a network engineer is in charge of the project. To provide the best possible network performance, it is his responsibility to configure the system in question. In your view, what measures should he take to complete the network setup?
(a) Suppose you are going to transmit a packet over OSI Network Model. Explain the working of Router, Gateway and Switch. Which device will be used if you face an issue of weak signals during transmission. Also, Mention on which level of OSI model these devices will work efficiently. (b) Attenuation, Distortion and Noise are the causes of Transmission impairment. What would be the solution or How these causes can be improved.
part 1: List down the services provided by the data link layer. part 2: Suppose there are 4 nodes sharing a broadcast channel using TDMA protocol. Suppose at time t=0: Node 1 has three frames to transmit, Node 2 has two frames to transmit, Node 3 has no frame, Node 4 has four frames to transmit. The length of time slot is 2 seconds whereas time needed to transmit one frame is 1 second. Explain how TDMA will work and how much time will be taken to transmit all of these frames? part 3: Do we need to use multiple access protocol in following cases? Lab computers connected to a layer 2 switch through Ethernet cables (star topology) Two computers in an Ethernet bus topology Your laptop is connected to BIIT network through a WiFi link Answer, yes or no and then justify…
assume that T = a
in a virtual network, there are three switches k1, k2 and k3. Source P need to communicate with destination T. The input port, output port and VCI for k1 is 8,4,55, input port, output and VCI for k2 is 6,5,75 and input port,ouport and VCI for k3 is 9,7,66. Conatruct the packet switch table for k1 k2,k3 and diagramatically represent the flow of setup request and acknowledgement.