(b) A balanced 200 V, three-phase generator is supply to a balanced delta-connected load. The voltage expression in time domain at the sources are: Vrn(t) = 200 cos(wt + 10°) V Vyn (t) = 200 cos(wt – 230°) V Von(t) = 200 cos(wt – 110°) V (i) Determine the voltages in phasor form. (ii) Draw the phasor diagram of the system and give your comments in word of leading or lagging. (iii) Determine the phase sequence of the set of voltages.

(b) A balanced 200 V, three-phase generator is supply to a balanced delta-connected load. The voltage expression in time domain at the sources are: Vrn(t) = 200 cos(wt + 10°) V Vyn (t) = 200 cos(wt – 230°) V Von(t) = 200 cos(wt – 110°) V (i) Determine the voltages in phasor form. (ii) Draw the phasor diagram of the system and give your comments in word of leading or lagging. (iii) Determine the phase sequence of the set of voltages.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the circuit in the figure; L1 load draws 15 kVA with lagging power factor 0.6. The L2 load draws 6 kVA with a leading power factor of 0.8. According to this; How many volts (rms) is Vs voltage?
If a A-connected load has a balanced impedance ZA 94 - 17° 2 and a voltage = = / VBC = 265 82° V rms, what is the magnitude of the current Ia (in A rms)? C V cn Van a Answer: n Von b Ia Ib 20 B IAB IBC ZA ZA ICA C
Three Impedances each of (9 - j18)N are connected in mesh across a three-phase 415V ac supply. Determine the phase current, line current, active power, reactive power drawn from supply. Also draw the Phasor diagram for the mesh connection and marks the Line current ,phase current line voltage and phase angle between phase current and pahse voltage. phase current (Ip) Line current real power reactive power
5 and 6
Q1: Consider the circuit shown in the following figure. (i) Find the phasor currents and voltages. (ii) Find the power delivered to the load. (iii) Reflect Vs and R1 to the secondary side. V₁= 1000/0° (~ V peak R₁ = 1000 £2 www 10:1 elle m 10 +j20 ZL
An AC supply voltage is represented by v = 325 Sin wt. Three loads are connected in parallel across the supply, and the currents through these loads respectively are: 1=8.48 Sin wt 12 = 4.24 Sin (wt - 15°) 3 = 6.36 Sin (wt + 90°) Which of the following is the supply current? O a. 13.49 75°A O b. 9.63222.65°A O c. 19.08275°4 O d. 7.49275 A
The following phasor diagram is: a. The phasor diagram of SG when it is running at lagging power factor b. The phasor diagram of SM when it is running at leading power factor c. The phasor diagram of SM when it is running at lagging power factor with the existence of RA d. The phasor diagram of IM when it is running at lagging power factor
A Time left 0:51 Z1 22 V sine sine B Let Z1 = 3+j4 ohm and Z2 = 3-j4 ohm. Let the current source phasor be I = j10 ampere and V = 50 volt and phase angle 0 degree. Both sources operate at 50 Hz. Real part of the Thevenin Voltage phasor between nodes A and B is Volt Imaginary part of the Thevenin Voltage phasor between nodes A and B is Volt Real part of the Thevenin Impedance between nodes A and B is Ohm
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: What are the RMS line current at load 1 and 2 respectively?
Find the sinusoidal and the rms phaser expression Vs = 120 sin (377t+0 degrees)
A synchronous generator is generating 395 V at 55 Hz at a field current of 3A. The e.m.f generated when the frequency is 35HZ and the field current is 2.3A is ..............