Athle phase a.c. distributor AB has:The distance from A to B is 500 m. The distance from A to C is 800 m.The impedance of each section is (6+j 8) /km.ABCThe voltage at the far end is maintained at 250 volt.Find: sending voltage, sending current, supply power factor and80 A60 Atotal voltage drop.0.8 lag. P.f0.6 lead. p.f

Answered: Image /qna-images/answer/5c3b908b-f705-4ccd-99d3-ea1e9d22ee0e.jpg

Answered: Athle phase a.c. distributor AB has:…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Similar questions

electrical engineering department plzz solve
A single phase a.c. distributor AB has: The distance from A to B is 500 m. The distance from A to C is 800 m. The impedance of each section is (6+j 8) /km. A B C The voltage at the far end is maintained at 250 volt. Find: sending voltage, sending current, supply power factor and 80 A 60 A total voltage drop. 0.8 lag. P.f 0.6 lead. p.f
Please help with the solution.
7. In the circuit below write the loop equations and set up (not solve) the matrix equation for the load current. Wiso 150 75 28 100
A 20 Ohm resistor is in series with a 30 Ohm Inductive reactance. If they are connected to a 40 Volt a.c. source, what is the phase angle between the voltage across the Inductive reactance, and the supply voltage (in degrees)? **Only give the magnitude. If you believe the current is lagging OR leading, give a positive value for the angle " I
A non-sinusoidal quasi-square wave voltage v(t) is applied to a nonlinear load, resulting in a non-sinusoidal current i(t). The voltage and current waveforms are shown below. Assume any values of your choice for Vp (≤ 200 V) and Ip (≥ 5 A). 1. calculate the average power and net power factor of the load. 2. The total load harmonic distrotion (THD) of the load current, assuming the smallest frquency term as fundamental.
A three-phase balanced load of 15A per phase is supplied by a steel wire armoured cable with a c.s.a. of 2.5mm². The voltage drop for this cable is 15mv/A/m and the circuit is 40m long. Calculate the voltage drop in the cable.
Q A 50 Hz, 13.6kv, 3-phase arternator with grounded neutral hasinductance of 12 mH per phase and is connected to busbar 16]through a circuit breaker. The capacitance to earth between thealternator and the location of circuit breaker is o.03pF per phase.Neglect the resistance of the alternator. Determine the following:i) Maximum value of re-striking voltag. ."ro". the contactsof circuit breaker.i1) Frequency of transient oscillationsiii) Maximum value of RRRVir') Average RRRV upto the first peak of transientoscillations.
The load flow data for the sample power system are given below. The voltage magnitude at bus 2 is to be maintained at 1.04 p.u.Determine the set of load flow equations at the end of first iteration by using N-R method. Impedance for sample system Bus Code Impedances line charging admittance 1-2 0.08 + j0.24 0.0 1-3 0.02 + j0.06 0.0 2-3 0.06 + j0.18 0.0 Schedule of generation and loads: Bus Code Assured Voltages Generation Load…
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Ztoad 500 236.87° ohm , and the transmission line's impedance is Zine = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
Fill in the table for a correctly wired duplex outlet (U.S. National Electric Code standards for voltage PARAMETER EQUATION and frequency). Note the used of double- subscript notation. You can assume a 0° phase reference for Vba(t). Vba(t) Vea(t) Vbe(t) Vba (Peak Phasor) Vea (Peak Phasor) Vbc (Peak Phasor) Vba (RMS Phasor) Vea (RMS Phasor) Vbc (RMS Phasor) A C
The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning