At 20°C, a rigid slab having a mass of 55MG is placed upon two bronze rods and one steel rod as shown. At what temperature will the stress in the steel rod be zero? For the steel rod, A=6,000 mm2, E=200 x 10 N/m2 and a=11.7 um/(m°C). For each bronze rod, A=6,000 mm? E=83 x 109 N/m2, and a=19.0 um/(m°C). M 23Dmm Bronze Steel Bronze

At 20°C, a rigid slab having a mass of 55MG is placed upon two bronze rods and one steel rod as shown. At what temperature will the stress in the steel rod be zero? For the steel rod, A=6,000 mm2, E=200 x 10 N/m2 and a=11.7 um/(m°C). For each bronze rod, A=6,000 mm? E=83 x 109 N/m2, and a=19.0 um/(m°C). M 23Dmm Bronze Steel Bronze

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is made of steel (E, =29x106 psi, as =6.5x106/F) and portion BC is made of aluminum (E, =10.4x10° psi, d a =13.33x10-6/F). Knowing that the rod is initially unstressed, determine the normal stresses induced in portions AB by a temperature rise of 110F. Answer in ksi. + 24 in. - -32 in.- A В 2--in. diameter 1-in. diameter
0.12
Due to loading, the plate is deformed into the dashed shape shown in the figure. Assume a = 39 in., b= 33 in., δ1= 0.1625 in., δ2= 0.1 in. Determine the average normal strain along the side AB? Determine the average shear strain in the plate at A relative to the horizontal and vertical axes? In micro rad
2. For the given state of stress shown in figure 2. 48 MPa Figure 2. a. Construct Mohr's circle for this plane stress. ||₁6 16 MPa 60 MPa Determine the principal stresses and principal planes.
Question: What is the effective vertical stress at Point A? Ym = 109 pcf 12 ft Layer 1 Ysat = 111 pcf 3 ft Ysat = 113 pcf 5 ft Layer 2 Not to scale O 1707 psf 2010 psf 2206 psf
Determine the force required to produce stress of 20 N/m2 on cross sectional area of 5 m2
5. The aluminum alloy bar has a circular cross section with 20-mm diameter and a shear modulus of 28 GPa. What is the magnitude of the maximum shear stress in the bar due to the uniformly distributed torque? y 8.5 kN-m/m 120 mm
Problem 1 39 ft (): Given: A steel railroad track which was installed at 30° F. Let E = 29 x 10 ^6 psi & a = 6.5 x 10^-6 / ° F Find: If the temperature reaches 125 ° F, determine a) The normal stress in the rails which are welded together to form a continuous track. b) The normal stress in the rails assuming the rails are 39 ft. Iong with 1/4" gap between them.
A structural steel bar with a 25 mm × 75 mm rectangular cross section is subjected to an axial load of 150 kN. Determine the normal stress in the bar.
Situation #4: Steel railroad rails 12 m long are laid with a clearance 4 mm at a temperature of 8°C. At what temperature will the rails just touch? What stress would be induced in the rails at that temperature if there were no initial clearance? Assume a =11.7 um/m°C and E = 200 GPa. %3D
Q: A piece of material is subjected to tensile stress of 70 N/mm² in one direction and a compressive stress of 50 N/mm² in a direction at right angles to the previous one. Find fully the stresses on a plane the normal of which makes an angle of 40 degree with the 70 N/mm2 stress.
Given data: Maximum principal stress-38 MPa Minimum principal stress=32.5 Mpa Find maximum shear stress