At 20 °C, a rigid slab having a mass of 55 Mg placed upon two bronze rods and one steel rod as shown. At what temperature will the stress in the steel rod be zero ? For the steel rod A=600mm? „E=200*10°MPA and a=11.7 um/(m.°C).For each bronze rods A=6000mm? ,E=83*10° N/m, and a=19.0 um/(m.°C). 55M 50mm Bronze Steel Bronze 250mm

At 20 °C, a rigid slab having a mass of 55 Mg placed upon two bronze rods and one steel rod as shown. At what temperature will the stress in the steel rod be zero ? For the steel rod A=600mm? „E=20010°MPA and a=11.7 um/(m.°C).For each bronze rods A=6000mm? ,E=8310° N/m, and a=19.0 um/(m.°C). 55M 50mm Bronze Steel Bronze 250mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylindrical rod has initial dimensions of length ? = 4 m andradius ? = 1 cm. When the rod is pulled in tension axially withan external force of ? = 200 kN, the rod deforms to newdimensions of length ?′ = 4.024 m and radius ?′ = 0.998 cm.Determine the modulus of elasticity of the rod and its Poisson’sratio. Assume the rod deforms in the elastic range.
A wrought iron pipe, 12-foot long, is rigidly fastened between two walls. Find the stress in ksi developed in the pipe due to a temperature rise of 83 degrees F. (Use E = 10,000 ksi and α = 6.4 x 10^-6 in/in/*F)
The mechanical system consists of two identical steel rods (A = 30 mm?, E = 200GPA, a = 15×106/°C) and a "rigid" beam AC. The beam is supported by a smooth pin at B. The nuts at A and C are initially tightened just enough to remove the slack, leaving the two rods stress-free. 1- Determine the axial stresses induced in rods (1) and (2) if the temperature of both rods is decreased by 60°C. 2- Determine the (small) angle e through which the beam AC would rotate due to this temperature change. -200 mm -80 mm A B -"Rigid" |(1) (2) 250 mm
PROBLEM NO. 4 In Fig. 4, determine the normal stress and change in length of the aluminum rod if the temperature was raised by 129 C. The 0.5-mm gap exists at 28 C (0.59 mm 399 mm A Aluminum A = 2888 mm² E = 75 GPa α = 23 x 10°/°C 258 mm B Stainless Steel A = 899 mm² E = 190 GPa α = 17.3 x 10/°C
A rigid horizontal bar ABC is supported by three vertical rods as shown. The system is stress free before the load is applied. After the load P is applied, the temperature of all three rods is raised by 110°F. Determine the magnitude of the normal stress in rod (1). Answer in MPa rounded-off to 2 decimal places. Rod (1) : E = 105 GPa; a= 22.0 x 10-5/°C A=500 mm² Rod (2): E = 200 GPa; a = 11.7 x 10-6/°C A=250 mm² 2,100 mm 4,400 mm (1) (2) B (2) P= 45 KN 2,100 mm I
Let's consider a rod having a solid circular cross- section with diameter of 4 mm and it is made of a material having a Young's modulus E = 120 Gpa and a Poisson's ratio of 0.33. If a tensile force F is subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F. Select one: F = 3427 N F = 2856 N F = 5712 N F = 8568 N F = 7140 N F = 2285 N
3. A 1.40 m long steel circular bar is acted upon by forces as shown in fig below. determine the total elongation of the bar. Take E steel=200Gpa and E brass = 85GN/m² 4 cm 3 cm 3 cm 40 kN 60 kN Steel 100 kN 80 kN Steel Brass 40 cm 60 cm 40 cm
4 In a plane stress condition, the components of stress at a point are ox= 20 MPa, oy = 80 MPa and Oxy = 40 MPa the maximum shear stress (in MPa) at the point is
-8 in.- -8 in.- (a) (b) Which of the following best explains why cylinder (b) has a higher longitudinal stress in its walls compared to cylinder (a)? Assume the gauge pressure of the fluid inside the cylinder is non-zero. O Cylinder (b) is supported at two locations Cylinder (a) is not free to deform in its longitudinal direction The vertical (longitudinal) pressure in cylinder (a) is transferred directly to the [bottom] support, bypassing the cylinder walls None of the above the longitudinal stress for both cylinders is the same
In class, we briefly looked at a generalized state of stress along an inclined plane, as shown in the figure below. Assume P = 16.9 kN, A = 83 mm², and 0 = 72°. P 0 A Determine the average normal stress on the shaded inclined cross-section, in MPa.
In the following structure if the temperature increases by 20 °C, determine the normal stress in Links (1) and (2). E (GPa) A (mm2) a (1/°C) 11.9x106 Link 1 200 310 Link 2 70 620 22.5x106 500mm 350mm F 千 100mm 300mm (2) 6kN 400mm