Assume a test cylinder that is used to find compressive strength of concrete failed when the load reached 85 kips. If the diameter of the test cylinder is 6", what is the compressive strength of concrete? (2 points) 6 in.

Assume a test cylinder that is used to find compressive strength of concrete failed when the load reached 85 kips. If the diameter of the test cylinder is 6", what is the compressive strength of concrete? (2 points) 6 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1.46: A contractor claims that the mean compressive strength for a concrete mix is 5000 psi (μ) and…

A: Given data contractor’s correct or not contractor’s correct or not

Q: What is the stress in a concrete cylinder 4 inches in diameter if it is supporting a load of 20,000…

A: Load applied, P = 20000 lb Diameter of cylinder, d = 4 inch Required:Stress in cylinder

Q: 2. The specified concrete strength f for a new building is 5000 psi. Calculate the required average…

A: (a) No Prior Test Results:Target Concrete Strength : 5000 psi(b) 20 Test Results with standard…

Q: 1. The specified concrete strength for a bridge is 5500 psi. You have 25 test results for the same…

Q: 100mm diameter cylindrical concrete specimen was tested for compressive strength. The sample failed…

Q: A concrete cylinder (6 x 12 in.), cured according to ASTM C 511 (100% RH and 23 °C) and tested at an…

A: We know, Stress = Load / Area Load at which the cylinder fail = 98342 lb Cross sectional area of…

Q: Q5. The compressive strength of concrete specimen follows a normal distribution with a mean value of…

Q: Answer the following conceptual questions on reinforced concrete behavior in bending (flexure). a.…

A: Reinforced concrete design is the process of planning, detailing, and specifying the components and…

Q: Situation 3 A compressive strength test were conducted to the following cylinder, Cylinder 1 3015…

A: Given data, Diameter d = 634 in

Q: The center-point loading flexure strength test was performed on a concrete beam having a cross…

A: To determine the flexure strength of concrete from the center-point flexure strength test. Give,…

Q: When describing the behavior of concrete under load, the popular belief is that concrete will crush…

A: L=12in

Q: 6′′ * 12′′ concrete cylinders were made of the same batch and separated at random to six equal…

A: (a) The expression for the compressive strength of concrete is given by, Here, CS is the…

Question

Assume a test cylinder that is used to find compressive strength of concrete failed when
the load reached 85 kips. If the diameter of the test cylinder is 6", what is the
compressive strength of concrete? (2 points)
6 in.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 given

VIEW

Step 2 calculation

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

11. Calculate the density (in kg/m³) and the compressive strength of the concrete (in MPa or N/mm?) for all samples from each type. Why the strength is different between the cubes and the cylinders? explain Cubic Sample of 100 mm Weight (kg) Load (kN) 1 2.52 655.8 2.59 670.9 3 2.47 675.9 Cubic Sample of 150 mm 1 8.43 1485 8.61 1492 3 8.53 1498 Cylindrical sample of 100×200 1 3.94 457.5 2 3.75 430.0 3 3.83 413.8 Cylindrical sample of 150×300 1 12.86 1056 13.0 1005 3 13.12 1020
Please solve the following problem with step by step soutions
A concrete test cylinder with a cross-sectional area of 28.3 in squared is to be tested in axial compression. Before loading two marks are scribed on the cylinder precisely 8 in apart (as shown in the figure below) when the load is 40,000 lb the marks are measured and found to be 7.997 in apart determine the E value for this concrete. Assume an approximately linear relationship between stress and strain.
Need some help with this question
Please give me both a and b answers a. If a concrete with 28 day compressive strength of 4500 psi is being poured, then it how much strength would you expect after 7 days(assuming good curing conditions)? Explain how you obtain the 7 day strength? b. Briefly explain the effect of water to cement ratio on concrete strength?
Use metric please
A concrete cylinder (6 x 12 in.), cured according to ASTM C 511 (100% RH and 23 °C) and tested at an age of 28 days in compression according to ASTM C 39 with a load rate of 30 psi/sec, fails at a load of 98,342 lb. The unit weight of the concrete is 145 lb/ft3. What is the compressive strength of the concrete cylinder in lb/in2? Round to the nearest whole number and do not include units when entering your answer.
2. You are an inspector on a job site, inspecting strength tests from a job with a design strength of 4500 psi. A total of 12 tests were performed on concrete from this job; the strength test results (in psi) are shown below. 4520 4840 4190 4960 4720 4890 4620 4290 4390 4680 4550 4620 Is this concrete acceptable?
What is the modulus of rupture where the sand-lightweight concrete has an f of 4000 psi? (The result must be written in an integer.) Answer:
In compressive strength testing of concrete, which type of concrete will give a more accurate result. 100mm by 100mm cubed concrete or 100mm cylinder concrete. Why?
A materials engineer is working in a research project to evaluate the effect of one type of admixture on the compressive strength of concrete. He tested eight mortar cubes made with admixture and eight others without admixture after 28 days of curing. The compressive strengths of cubes in psi with and without admixture are shown in Table P6.40.Using the statistical t-test, is there a significant difference between the meansof the compressive strengths of the two cement mortars at a level of signifi-cance of 0.10?
Three 100*200 mm cylindrical concrete specimens were tested for 28 days compressive strength and show 30.5 MPa, 29.6 MPa and 32.8 MPa compressive strength. a) What is the average compressive strength of this concrete? b) What is the approximate tensile strength of this concrete? c) What is the approximate modulus of elasticity of this concrete? For the toolbar, press ALT+F10 (PC) or ALT+FN+F10 (Mac). BIU Paragraph Arial 10pt A v x² X, +, 田用国田用因 Ť } !!