As shown below, a 38 kg bar that is 1.3 m long is set up to rotate about its center (the yellow circle). Force B is acting 28 cm from the left end of the bar. Express each answer using appropriate mks units. A = 42 N B = 38 N C = 26 N 8A = 41° 08 = 37° B Determine each individual torque, the net torque, and the direction the bar will rotate. TA= TB = TC= Thet Direction of rotation=-- Choose direction ---

As shown below, a 38 kg bar that is 1.3 m long is set up to rotate about its center (the yellow circle). Force B is acting 28 cm from the left end of the bar. Express each answer using appropriate mks units. A = 42 N B = 38 N C = 26 N 8A = 41° 08 = 37° B Determine each individual torque, the net torque, and the direction the bar will rotate. TA= TB = TC= Thet Direction of rotation=-- Choose direction ---

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Needs Complete typed solution with 100 % accuracy.
In unit-vector notation, what is the net torque about the origin on a flea located at coordinates (0, -7.23 m, 1.81 m) when forces F₁ = (4.92 N) and F₂ = (-6.97 N) act on the flea? Number 48.187 î 0 Ĵ 0 k Units N-m
The fishing pole in the figure below makes an angle of 20.0° with the horizontal. What is the magnitude of the torque exerted by the fish about an axis perpendicular to the page and passing through the angler's hand if the fish pulls on the fishing line with a force F = 110 N at an angle 37.0° below the horizontal? The force is applied at a point L = 2.04 m from the angler's hands. N.m Need Help? Watch It Additional Materials 20.0° eBook 120.0⁰ 37.0° F
A torque of 60 N•m producing a counterclockwise rotation is applied to a wheel about its axle. A frictional torque of10 N•m acts at the axle.a. What is the net torque about the axle of the wheel?b. If the wheel is observed to accelerate at the rate of 2 rad/s under the influence of these torques, what is the rotational inertia of the wheel? Use the right formula to solve and get the correct answer
Suppose you exert a force of 167 N tangential to a 0.255 m radius 75.0 kg grindstone (a solid disk). (Give your answers to at least 2 decimal places.) (a) What torque (in N m) is exerted? (Enter the magnitude.) 42.585 N.m (b) What is the angular acceleration (in rad/s²) assuming negligible opposing friction? (Enter the magnitude.) 2.44 X rad/s² (c) What is the angular acceleration (in rad/s²) if there is an opposing frictional force of 22.6 N exerted 1.75 cm from the axis? (Enter the magnitude.) rad/s²
A block of mass MB=2.5 kg is attached to a pulley of mass MP=2MB and R=10.0 cm (Icyl = 1/2MR2) and is pulled from the other side with force F=30.6 N with a massless string as in Figure 3. A. Write an expression for Newton's 2nd Law for the block. B. Write an expression for Newton's 2nd Law (for torque) for the pulley. C. Calculate the acceleration of the system and indicate the direction.
The two blocks in (Figure 1) are connected by a massless rope that passes over a pulley. The pulley is 16 cm in diameter and has a mass of 2.7 kg. As the pulley turns, friction at the axle exerts a torque of magnitude 0.75 Nm. If the blocks are released from rest, how long does it take the 4.0 kg block to reach the floor?
Wolverine has an arm that is 1[m] long and claws that are 0.5[m] long. He's trying to knock over a wall. His shoulder can exert a torque of 1,500[N-m]. What is the ratio of force on the wall with vs without his claws extended? 1.5[m] point Pivot F /F Adamantium Wall without with claws claws A. 2/3 F Wolverine with В. 3/2 with claws С. 1 1.0[m] Pivot Adamantium D. I don't know but the torque direction is point Wall E. I don't know but the torque direction is Fwithout Wolverine Bare hands
Suppose you exert a force of 172 N tangential to a 0.295 m radius 75.0 kg grindstone (a solid disk). (Give your answers to at least 2 decimal places.) (a) What torque (in N · m) is exerted? (Enter the magnitude.) N. m (b) What is the angular acceleration (in rad/s2) assuming negligible opposing friction? (Enter the magnitude.) |rad/s? (c) What is the angular acceleration (in rad/s?) if there is an opposing frictional force of 22.6 N exerted 1.75 cm from the axis? (Enter the magnitude.) |rad/s?
P=V+18+90² 2.Ifr= {Si}mand F = (-10k) N, the moment rx F equals { _N.m. P₁-
Please refernece attachment. See image for more info.
To study torque experimentally, you apply a force to a beam. One end of the beam is attached to a pivot that allows the beam to rotate freely. The pivot is taken as the origin or your coordinate system. You apply a force of F = Fx i + Fy j + Fz k at a point r = rx i + ry j + rz k on the beam. Part a) Calculate the magnitude of the torque, in newton meters, when the components of the position and force vectors have the values rx = 3.71 m, ry = 0.075 m, rz = 0.085 m, Fx = 1.2 N, Fy = -7.6 N, Fz = 1.2 N. Part b) If the moment of inertia of the beam with respect to the pivot is I = 72 kg˙m^2, calculate the magnitude of the angular acceleration of the beam about the pivot, in radians per second squared.