As in the figure, a pressurized cylindrical container is made of 12 mm thick plate as shown in the figure. The pressure in the cylinder is given as 1400 kPa and axial load F = 70 kN. According to the cylinder's inner D = 1.5 m; Find the normal stress and shear stress occurring along the welding seams in the cylinder. 70 KN Kaynak dieis dule

As in the figure, a pressurized cylindrical container is made of 12 mm thick plate as shown in the figure. The pressure in the cylinder is given as 1400 kPa and axial load F = 70 kN. According to the cylinder's inner D = 1.5 m; Find the normal stress and shear stress occurring along the welding seams in the cylinder. 70 KN Kaynak dieis dule

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.19P: At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with...

See similar textbooks

Related questions

Q: a. Take a cut through the section where the AB and BC segments are connected (shown in the figure at…

A: we are to determine the stress distribution at section B, and the load at point C

Q: The rectangular bar shown is connected to a support bracket with a 27 mm diameter pin. The width of…

Q: In the assembly of the bronze tube and steel bolt shown in the figure, the pitch of the bolt thread…

A: GIVEN DATA -

Q: 3 - A cylindrical thin-walled pressure vessel was made by welding components together in a helical…

A: The given information in the problem is shown in the following attached image:

Q: 3. As in the figure, a ship can move both with the wind and with a diesel engine. your ship The mast…

Q: Consider a rectangular plate shown in Figure 1 and is subjected to a compressive stress of 2.5 MPa…

A: Compressive stress on the x-axis, Tensile stress on the y-axis, The value of the angle,

Q: An aluminum right-circular cylinder surrounds a steel cylinder as shown in Fig. 1-29. The axial…

A: Given Data The axial compressive load applied is: P=200 kN The temperature drop is: T=20 K=253.15°C…

Q: . Find the thickness of the flat end cover plates for a 1 N/mm2 boiler that has a diameter of 600…

Q: 125 x 95 x 10 mm angle is welded to a frame by two 10 mm fillet welds, as shown in Figure bellow. A…

A: Given that, Thickness of toe=10 mm,

Q: Find the maximum shear stress for the stress case given in the figure.

A: Given Data The stress acting in x direction is: σx=100 MPa The stress acting in y direction is:…

Q: (3) The cantilever bar as shown on next page is made of a brittle material. At D, F-300 lb, EF-250…

A: Given data :Material of cantilever Bar= Cast iron (Brittle Material)At D: Fx= 300 lb, Fy= 250 lb,…

Q: wo 10-mm thick plate members are to be connected using straps of the same thickness and 12-mm…

Q: Bronze 2 m Steel |1.0m -l0,6 ml–1.0 m– 0.8 m- 50 kN -10m- (a)

A: There are three static equilibrium equations, horizontal force balance, vertical force balance, and…

Q: PROBLEM: Find the values and plot the distribution of stress over the cross section of the upright…

A: The Answer is below

Q: The coupling as shown in figure is made from steel has rectangular cross section is designed to…

Q: A cylindrical pressure vessel is made by shrinking a brass shell over a mild steel shell. Both…

A: Given Data The wall thickness is:hwall=6 mm The external diameter of the brass tube is:De=750 mm…

Q: (3) The cantilever bar as shown on next page is made of a brittle material. At D, F-300 lb. F-250…

A: Given data :Material of cantilever Bar= Cast iron (Brittle Material)At D: Fx= 300 lb, Fy= 250 lb,…

Q: The axial com An aluminum right-circular cylinder surrounds a steel cylinder as shown in Fig. load…

A: Given data as per question Axial compressive load =200 KN Drop-in temperature =20 k =-253.15 0 c…

Q: A rectangular plate (0 =21°) is formed by welding two triangular plates shown in figure. The plate…

A: Given data θ=21° Compressive stress=2.9 Mpa. Tensile stress=19 Mpa.To determine The normal…

Q: Define the main difference between thick and thin cylinders and give an example for each type of…

Q: Find the internal normal stress in all relevant segments of the bar in the picture. The bar has a…

Q: A rectangular plate (0 =25°) is formed by welding two triangular plates shown in figure. The plate…

Q: loading Fas shown in figure. Both legs of the fillets A fillet welded joint is subjected to…

Q: Two circular rods of 50 mm diameter are connected by a knuckle joint, as shown in Figure 1, by a pin…

Q: The cylinder pressure vessel has an inner radius of 1.25 m and a wall thickness of 15 mm. It is made…

A: Given data:- radius r = 1.25 m Thickness t = 15 mm Angle = 45° Pressure P = 10 Mpa

Q: Pmax: i kN

Q: 70 kN Kaynak dikiş đüzlemi D

Q: A rectangular plate (0 =23°) is formed by welding two triangular plates shown in figure. The plate…

A: GIVEN: σx=-2.3 MPa σy=13 MPa θ=23° TO FIND: The normal stress and Shear stress on the weld plane.

Q: a. Calculate the largest tensile and compressive stresses that occur in section a-a shown in the…

Q: A pressurized cylindrical container, as in the figure, is made of 12 mm thick plate as shown in the…

Q: 2. For the joint shown in the figure, calculate: (a) The largest bearing stress between the pin and…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

As in the figure, a pressurized cylindrical container is made of 12 mm thick plate as
shown in the figure. The pressure in the cylinder is given as 1400 kPa and axial load F
= 70 kN. According to the cylinder's inner D = 1.5 m; Find the normal stress and shear
stress occurring along the welding seams in the cylinder.
70 KN
Kaynak dieis
dule

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
At a point on the web of a girder on an overhead bridge crane in a manufacturing facility, the stresses arc known to be x = —4300 psi, a = 1700 psi, and r = 3100 psi (the sign convention for these stresses is shown in Fig, 7-1). A stress clement located at the same point in the structure (but oriented at a counterclockwise angle 0, with respect to the _y axis) is subjected to the stresses shown in the figure {b, r», and 2100 psi). Assuming that the angle 8Xis between zero and 90°, calculate the normal stress trA, the shear stress ta, and the angle Bv
Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses on the rotated element are sx1=10 ksi, sy1= -12 ksi, and tx1y1= -5 ksi. Find the state of plane stress on the clement if it is rotated clockwise to align the x3 axis with the longitudinal axis of the rods.
The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial .is in the and is subjected to stresses a, = 6250 psi and a. = -1750 psi, as shown in the figure. Using Mohr s circle, determine the following: (a) The stresses acting on an element oriented at a counterclockwise angle ? = 550 from the x axis. (b) The maximum shear stresses and associated norm al stresses. Show all results on sketches of properly oriented elements.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial stress and is subjected to stresses a = -48 MPa and ay = 19 MPa, as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at a counterclockwise angle ?? = 25° from the x axis. (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
A cylindrical tank with hemispherical heads is constructed of steel sections that are welded circumferentially (see figure). The tank diameter is 1.25 m, the wall thickness is 22 mm, and the internal pressure is 1750 kPa, (a) Determine the maximum tensile stress h in the heads of the tank. (b) Determine the maximum tensile stress c in the cylindrical part of the tank. (c) Determine the tensile stress <7W acting perpendicular to the welded joints, (d) Determine the maximum shear stress rtiin the heads of the tank. (e) Determine the maximum shear stress tcin the cylindrical part of the tank
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
The polyethylene liner of a settling pond is subjected to stresses ax= 350 psi. a = 112 psi. and = -120 psi, as shown by the plalte-stress element in the figure part a. Determine the normal and shear stresses acting on a seam oriented at an angle 01300 to the element, as shown in the figure part b. Show these stresses on a sketch of an element having its sides parallel and perpendicular to the seam.
The stresses at a point on the down tube of a bicycle frame are trx= 4800 psi and t = -1950 psi (see figure). It is known that one of the principal stresses equals 6375 psi in tension, (a) Determine the stress (b) Determine the other principal stress and the orientation of the principal planes, then show the principal stresses on a sketch of a properly oriented clement.
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.