Find the maximum shear stress for the stress case given in the figure. Formül;60 MPаTL1- 0,630b/a)Tmaks =Cab? · $ =C,ab³G' 5²5 için c = c2 = :45 MPaM2(lzy.z- ly y) + My(1,.z – Izy.y)Iz.ly – lzy?Ox + dy, tan28p -МуO = -T• Ox =2tAVQIt2TxyOx - dy100 MPa100MPAOx + dy Ox- 0yOx = -2cos20 + Txysin20 , Jort =Ox + OyOx - Oysin20 + Txycos20 , Imaks.min =2+ TyTx'y' = -45 MPa60 MPaTmaks =Şekilde verilen gerilme durumu için maksimum kayma gerilmesini bulunuz.80,00 MPa129,24 MPa49,24 MPa138,75 MPa114,25 MPa

Given Data The stress acting in x direction is: σx=100 MPa The stress acting in y direction is:…

Answered: Find the maximum shear stress for the…

Engineering

Mechanical Engineering

Find the maximum shear stress for the stress case given in the figure.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The round bar in the figure is made of steel (E-207 GPa). The load F has a magnitude of 100 N. You will be finding the stress at point A. 20 mm dia 200 mm 100 mm
4 kN 3 kN 375 mm B 375 mm 750 mm As shown in the figure, the shaft is supported by bearings A and B and is subjected to a concentrated load. Material A-36 steel Diameter: 50 mm Find the maximum displacement and maximum stress. 1) Determine the theoretical stress value using the stress formula due to bending load. 2) Model with a solid model to obtain stress values and displacements at Creosimulate. 3) Model with Beam model to obtain stress values and displacements at Creosimulate.
-L2 F1 L1 F2 A solid member with a diameter of 35 mm is subjected to loads as shown in figure above. If L1=62 mm, L2=102 mm, L3=49 mm, F1=1467 N, and F2=2420 N; Determine the normal stress (MPa) at point K. Use - sign if it is compressive. Determine the shear stress (MPa) at point K. Use proper sign. Determine the magnitude of the maximum in-plane shear stress (MPa) at point K.
In the figure, the steel shaft with a diameter of 36 mm is 240 mm diameter pulley. Belts also formed under given angles If the tensile Forces are 2400N and 400N, the shaft at point K on the x-z plane Calculate the normal and shear stresses. Plotting the stress state for this point show me The shaft can carry safely if shear stress em=100 MPa Using the Greatest Transformation Energy (vonMises) hypotheses, the K point Show if it is safe.
1)In a thin plate, the state of stress prevails according to the figure. Calculate the principal stresses and their directions (using both equations and Mohr's stress circle). Show the result in a figure. σx = 40 MPa; σy = 50MPa and τxy = 30 MPa 2)A cylindrical pin made of carbon steel is loaded with a maximum possible twisting moment Mv. Maximum allowedshear stress is Tmax = 40 MPa. The pin has the diameter measurement d = 50 mm, and the length measurement L = 250 mm.Calculate the free end distortion θ in degrees. G=80 GPa.
Calculate the main stress plane and main stress at the plane stress conditions as shown in the following figure.
For the assembly shown in Figure 2, the cross section of the pipe at section B has outer diameter of 100 mm and inner diameter of 80 mm. points N and L are located on X-axis at outer surface of the pipe while points K and M are located on z-axis at outer surface of the pipe. At which point of the four (K, L, M or N) the principle stresses are largest. Calculate the principle stresses at this point.
(3) The cantilever bar as shown on next page is made of a brittle material. At D, Fx-300 lb. F-250 lb, and F-100 lb. Determine the precise location of critical stress element at the cross section at A. Determine the magnitude for each of the stress components considering the stress concentration at A. Find the principal stresses and the maximum shear stress at this location. 2 in 1-in dia. -in R. 12 in
Consider the circular bent rod with diameter 20 mm. The free-end of the bend is subjected to loads as shown in the figure below. Find the total shear stress, 7 at point (Hint: includes both torsional shear stress and transverse shear stress) in section a-a in MPg: Enter only numeric value without units upto 1 digit after decimal point, but with correct sign. 200 mm 200 mm NA al D. R. Section a-a 400 N 800 N
The cantilever beam with a rectangular cross-section is under the loading P as shown in the figure. P Part A At an arbitrary cross-section, a - a the state of stress is obtained at various points (point 1 - 5, where point 3 is the midpoint). Select all that describe the stress at the cross-section a - a correctly. O The cross-section a-a has three internal loadings, i.e., shear force, normal force, and bending moment. O The normal stress by bending moment at point 5 is zero. O The maximum shear stress by shear force occurs at the same point as the maximum normal stress by bending moment. O The maximum shear stress by shear force occurs at point 3. O Point 1 develops compressive normal stress by bending moment. O The shear stress by shear force at point 1 is zero. Submit Request Answer
In the figure, the steel shaft with a diameter of 36 mm is 240 mm diameter pulley. Belts also formed under given angles If the tensile Forces are 2400N and 400N, the shaft at point K on the x-z plane Calculate the normal and shear stresses. Plotting the stress state for this point show me The shaft can carry safely if shear stress em=100 MPa Maximum Shear stress (Tresca)
40 mm Calculate the greatest draft and compression stresses in the a-a section when a force of P = 8000 N is applied to the vice in the figure (dimensions are in mm). 10 mm 50 mm 10 nun section a-a