please solve asap. An NPN BJT in a common emitter circuit is known to be working in theactive region with gain Bemitter is AUBE= 100. The voltage change between base and= 10 mV. Please find out the input resistance rpe, basecurrent change Alg and collector current change AIc respectively, whenthe base current Ig is equal to 16 µA and 32 µA.

Input resistance is 1.625 kilo ohms Collector current is 1.6 milli ampere

An NPN BJT in a common emitter circuit is known to be working in the active region with gain B = 100. The voltage change between base and emitter is AUBE 10 mV. Please find out the input resistance rpe, base current change Alg and collector current change Alc respectively, when the base current Ig is equal to 16 µA and 32 µA.

An NPN BJT in a common emitter circuit is known to be working in the active region with gain B = 100. The voltage change between base and emitter is AUBE 10 mV. Please find out the input resistance rpe, base current change Alg and collector current change Alc respectively, when the base current Ig is equal to 16 µA and 32 µA.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. Write the answer for the following questions. A. Define Electric field strength. B. What are the factors affecting the capacitance of a parallel plate capacitor? C. State the coulombs Law with its equation.
"Given the potential function V = x²ytz+3), determine the electric potential at (3, 4, -6)." -108 ml/C 324 mJ/C -108 J/C 324 J/C
The student engineer of a campus radio station wishes to verify the effectiveness of the lightning rod on the antenna mast (as shown). The unknown resistance Rx is between points C and E. Point E is a true ground, but it is inaccessible for direct measurement because this stratum is several meters below the Earth’s surface. Two identical rods are driven into the ground at A and B, introducing an unknown resistance Ry. The procedure is as follows. Measure resistance R1 between points A and B, then connect A and B with a heavy conducting wire and measure resistance R2 between points A and C. (a) Derive an equation for Rx in terms of the observable resistances, R1 and R2. (b) A satisfactory ground resistance would be Rx < 2.00 Ω. Is the grounding of the station adequate if measurements give R1 = 13.0 Ω and R2 = 6.00 Ω? Explain.
Q1/ For the network shown in figure (Q1), the switch has been in position "a" for a long time. At t-0, the switch moves and stays at position "b". Determine an expression for the inductor current iL(t) when t20 using the general solution formula. 5e ielt) 12 2 tzo 6052 lom h 72V T24oV
Consider the R-C circuit. we idealise the emf to be constant and have zero internal resistance. We begin with capacitor initially uncharged. At initial time t=0, the switch was closed. Answer the questions attached.
Determine the differential equation for the following mechanical system
please sir solve these 2 questions
Solve
Please answer quickly.
Thank you And please kindly write legibly because I'm having a hard time reading, guessing, and understanding the handwriting of different experts recently. Thanks Please refer to the photo below. Activity: Series and Parallel Capacitance
Q1) A 100 cm in length cantilever beam subjected to an applied force P. The strain &, at the bottom surface of the beam has a relation with the applied force F is given by &, = 2 x 10-9P where P changes form (0N to 1000KN). The strain can be measured using a120n strain gauge with gauge factor of 2. Design a measuring device that can read the applied load and feeds the required signal to a computer using ten bits ADC accuracy. The system should compensate the temperature effects.
Don't use ai to answer I will report your answer .. Solve it Asap with explanation all parts