3. Consider the following scenario: A civil engineering student measures the resistivity of a particular cylindrical wire for different lengths L by tapping at points the wire from 0.1 m to 1 m in steps of 0.1 m. The radius of the wire is 0.YZ mm. The experiment is carried out under following circumstances: a) The best line has been drawn through the points given below and determine the resistivity of the wire from the slope of the plot between blue marked points. b) Based on the value of resistivity you calculated, what is the material wire resistor made of? Make sure everything is in ohms and meters, otherwise your units will not work out correctly in the end! Table 1. Resistivity of Some Common Materials. Material Silver Сорper Gold Aluminum Steel Resistivity p ( Q-m ) 1.59x10 1.72×10* 2.44×10 2.65×10 2x10 2.2x107 Lead Manganin (Cu, Mn, Ni alloy) Constantan (Cu, Ni alloy). Mercury Nichrome (Ni, Fe, Cr alloy) 4.4x10 4.9x10 9.6x10 Ix10 9 - 8 - 7- 6- 5 3- 2 0,0 0,2 0,4 0,6 0,8 1,0 L(m)

3. Consider the following scenario: A civil engineering student measures the resistivity of a particular cylindrical wire for different lengths L by tapping at points the wire from 0.1 m to 1 m in steps of 0.1 m. The radius of the wire is 0.YZ mm. The experiment is carried out under following circumstances: a) The best line has been drawn through the points given below and determine the resistivity of the wire from the slope of the plot between blue marked points. b) Based on the value of resistivity you calculated, what is the material wire resistor made of? Make sure everything is in ohms and meters, otherwise your units will not work out correctly in the end! Table 1. Resistivity of Some Common Materials. Material Silver Сорper Gold Aluminum Steel Resistivity p ( Q-m ) 1.59x10 1.72×10* 2.44×10 2.65×10 2x10 2.2x107 Lead Manganin (Cu, Mn, Ni alloy) Constantan (Cu, Ni alloy). Mercury Nichrome (Ni, Fe, Cr alloy) 4.4x10 4.9x10 9.6x10 Ix10 9 - 8 - 7- 6- 5 3- 2 0,0 0,2 0,4 0,6 0,8 1,0 L(m)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Motor driven by PWM using full-bridge operation provides finer resolution than half-bridge operation. True or False?
Could you answer this question in details and giving examples if possible. Thanks a lot. - Explain meaning of Vetronics. This question is related with the Embedded system ( Electrical electronic engineering)
Answer the question quecly please
Draw circuit diagram of a cross over in a two speaker system? What is its operation?
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
Follow the instructions. Kindly provide a COMPLETE and CLEAR solution. Answer it ASAP because I really need it right now. Answer should be typewritten. Provide the following:Step 1. Solve for kStep 2. Solve for Tk (forward path gain)Step 3. Identify the loop gains (TL)Step 4. Identify the nontouching loops taken two at a time TNL(2 time)Step 5. Identify the nontouching loops taken three at a time TNL(3 time)Step 6. Identify the nontouching loops taken four at a time TNL(4 time)Step 7. Solve for component ∆Step 8. Solve for component ∆k (Note: We form ∆k by eliminating from ∆ the loop gains that touch the kth forward path)Step 9. Substitute on the equation for transfer function
Choose True or False
Get the same shape required and Give proper label and title by using OCTAVE and write the program
Topic Air Blast Circuit Breaker? Individual submission only accepted.  Minimum 350 words.  Reference should be added. .
Whats oms law??
Follow the instructions. Kindly provide a COMPLETE and CLEAR solution. Answer it ASAP because I really need it right now.Answer should be typewritten. Provide the following:Step 1. Solve for kStep 2. Solve for Tk (forward path gain)Step 3. Identify the loop gains (TL)Step 4. Identify the nontouching loops taken two at a time TNL(2 time)Step 5. Identify the nontouching loops taken three at a time TNL(3 time)Step 6. Identify the nontouching loops taken four at a time TNL(4 time)Step 7. Solve for component ∆Step 8. Solve for component ∆k (Note: We form ∆k by eliminating from ∆ the loop gains that touch the kth forward path)Step 9. Substitute on the equation for transfer functionFormula:∆ = 1- ΣTCL + ΣTNL(2 time) - ΣTNL(3 time)+ ΣTNL(4 time)+ ......∆k = ∆ - ΣTL touch kth forward path