An insulated piston-cylinder device contains 5 L of saturated liquid water at a constant pressure of 150 kPa. An electric resistance heater inside the cylinder is now turned on and 2200 kJ of energy is transferred to the system. a) Sketch a schematic diagram of the system and label all given information. b) Determine mass of the water, kg. c) Determine final enthalpy of the water, kJ/kg.

An insulated piston-cylinder device contains 5 L of saturated liquid water at a constant pressure of 150 kPa. An electric resistance heater inside the cylinder is now turned on and 2200 kJ of energy is transferred to the system. a) Sketch a schematic diagram of the system and label all given information. b) Determine mass of the water, kg. c) Determine final enthalpy of the water, kJ/kg.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the Piston-cylinder Assembly, water in the form of hot steam with a mass of 1 kg at a pressure of 500 kPa and a temperature of 500°C is first cooled to a temperature of 120°C in a constant volume, and then condensed by cooling until the water becomes a saturated liquid at a constant temperature.a) draw a T-v diagram of state changesb) find the work done throughout the state changes.c) find the heat transfer from the piston cylinder Assembly to the environment.Note: changes in kinetic and potential energies are negligible.
A sealed rigid tank whose volume 1.00 m contains 2 kg of liquid water plus water vapor. Initially the temperature is 20 °C and the internal energy is 103.8 kJ/kg. The tank is heated until the temperature reaches 95 °C. Determine: a) The specific volume at initial state b) The quality of the mixture at the final temperature of 95 °C c) The heat that went into the tank in kJ.
The piston-cylinder assembly, which initially contains 5 kg of water at 20 ° C and 400 kPA pressure, has a dryness level of 0.41 when it comes to the upper stoppers after the heat given at constant pressure. As the saturated steam is obtained after the heat given in constant volume; a)final pressure and temperature. b)Plot the state change on a p-v and t-v diagram. c)work done after the process and heat transfer
Saturated water vapor initially at a pressure of 225 kPa and volume 0.01 is contained in a piston cylinder assembly. The water undergoes two processes in series:Process 1-2: Constant volume process till the pressure is 2 bars.Process 2-3 : Constant pressure process till the volume is doubled.Determine:a) the temperature at state 3b) the total amount of work for process 1-3c) the total amount of heat transfer for process 1-3. v1 (m3/kg) Format : 0.72765 m (kg) Format : 0.0622 v3 (m3/kg) Format : 7.8553 W2-3 (kJ) Format : 5.7285 u1 (kJ/kg) Format : 2832.5 u2 (kJ/kg) Format : 7592.79 Q1-2 (kJ) Format : -4.87 u3 (kJ/kg) Format : 8499.67 Q2-3 (kJ) Format : 60.34 Q1-3 (kJ) Format : 5.9 T3 (oC) Format : 822.09
A 2 m^3 rigid tank contains water. Initially, 10 L of this water is in saturated liquid phase. The remaining volume of the tank is filled with saturated vapor. The pressure inside the tank is 2 bar. Based on thisinformation:a) What is the total mass of water inside the tank at that moment? b) What is the quality of this mixture?c) What is the average specific volume of this mixture? d) The tank is now heated until the pressure inside is 8 bar. Find the final temperature of water and the total heat input required for this process. Note: Take water as pure substance
I need solve Q3 only
The system total energy is always conserved, when (mark all): a) a closed system undergoes a process; b) an isolated system undergoes a process; c) a control volume system undergoes a process; d) an open system undergoes a process.
8. During the drive, you can take fresh air using the conditioning system available in the automobile. However, you should slightly open (about 1 cm) your window for the exhausting some air, according to the mass balance principle. If you open your window completely, the intake of fresh air and exhaust of polluted air will deteriorate. Based on this information, what do you think about pressure balance? A) Pautomobile Poutside B) Pautomobile = Poutside C) Pautomobile > Poutside D) Pautomobile SPoutside 9. Which temperature measurement device is mostly used in industry? A) Gas thermometry B) Thermocouples C) Bimetallic thermometers D) Thermal Camera 10. Which measuring instrument should be preferred to convert qualitative measurement with thermochromic liquid crystals to quantitative data. A) Resistance Temperature Detector B) Thermocouples C) Bimetallic thermometers D) Thermal Camera 11. Which of the temperature measurement technique is used for visual warning of certain temperature…
Air enters an adiabatic air compressor with a pressure of 1 bar, a temperature of 300 K and a flow rate of 3 m3/minute; It leaves at 3 bar pressure and 440 K. a) Compressor output flow (m3/min)b) The absolute value of the power that must be given to the compressor shaft (kW)
Determine the phase of the refrigerant R-134a at temperature of 48 C and pressure of 1 MPa. a)saturated liquid b)superheated refrigerant c)saturated vapor d)compressed refrigerant e)saturated mixture f)Other:
In a fixed volume tank, there is initially 0.8 kg of superheated water vapor at a temperature of 300°C and a pressure of 1 MPa. The final temperature drops to 120°C by drawing heat from the container and it is observed that the water has partially condensed. According to this; a) Volume of the tank b) Final state dryness x=?c) The amount of heat withdrawn from the tank as absolute value?
5. "Wet steam" at 200 kPa has 40% of its mass as liquid. The water is contained in a spring-loaded piston-cylinder, with an initial volume of 3 m'. The steam is now heated until its volume is 4.535 m and its pressure is 500 kPa. Determine: a) The final temperature b) c) The work done by the steam The total heat transferred Spring d) Show the process on a P-v diagram Steam