An industrial soft drink production plant needs to implement a quality control system for its bottling line. The system must monitor four critical parameters and activate different alarms depending on the conditions detected. Design a digital circuit with 4 inputs and 3 outputs for this purpose, Design the logic circuit for this control system using Karnaugh maps to simplify the Boolean functions of each output. The final design must be efficient and use as few logic gates as possible. Inputs: A: Carbonation level (0 = normal, 1 = high) B: Liquid temperature (0 = normal, 1 = elevated) C: Line pressure (0 = normal, 1 = low) D: Filling speed (0 = normal, 1 = low) Outputs: X: Minor adjustment alarm (triggered when an odd number of parameters are out of range) Y: Major revision alarm (triggered when at least three parameters are out of range) Z: Adjacent parameters alarm (triggered when exactly two adjacent parameters are out of range)

An industrial soft drink production plant needs to implement a quality control system for its bottling line. The system must monitor four critical parameters and activate different alarms depending on the conditions detected. Design a digital circuit with 4 inputs and 3 outputs for this purpose, Design the logic circuit for this control system using Karnaugh maps to simplify the Boolean functions of each output. The final design must be efficient and use as few logic gates as possible. Inputs: A: Carbonation level (0 = normal, 1 = high) B: Liquid temperature (0 = normal, 1 = elevated) C: Line pressure (0 = normal, 1 = low) D: Filling speed (0 = normal, 1 = low) Outputs: X: Minor adjustment alarm (triggered when an odd number of parameters are out of range) Y: Major revision alarm (triggered when at least three parameters are out of range) Z: Adjacent parameters alarm (triggered when exactly two adjacent parameters are out of range)

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
1) Here is a Digital Logic question on analysis of clocked sequential circuits with the answer. Please explain what the teacher did and why they did it. I need you to explain how they got the answer.
Solve the problem and simplify the output function using Quine–Mc Cluskey Methods. The following requirements must be met in solving the problem. Requirement:a. Truth Tableb. Timing Diagramc. Quine – Mc Cluskey Method d. Logic Diagram A private company wants to decide on a certain issue. Each of the four officials has an equal share of voting right. At least two of them must approve the solution in order to implement it. Each of them has a switch which closes to vote YES and open to vote NO.
(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
This question is from the subject Digital Logic Design. Assume your register number SF20-BEC-xxx (excluding the dashes -) is in Hexadecimal, where xxx are the three digits of your registration number. a) Represent your registration number in the binary.b) Split the ten digits of your registration into two Hexadecimal numbers M and N, where the left most five digits make number M and the right most five digits make number N. Using r’s complement, subtract N from M. In other words, calculate M – N. Solve the question for registration no SF20-BEC-156.
H.W: Reduce the combinational logic circuit in Figure below to a minimum form.
Design a combinational circuit with 3-inputs and 1-output. The output is equal to logic-1 when the binary value of the input is less than 3. And the output is logic-0 otherwise.
Question iii please help......
answere fast please question from DIGITAL LOGIC DESIGN TOPIC : Designing Combinational Logic You are designing a water level circuit using 74ALS151 (8 to 1 Multiplexer IC)* When input is 0000 that means tank is empty.* When input is 1111 that means tank is full.* When input is below 5, that means water level is low.* So, make a circuit using 74ALS151 Multiplexer IC that shows a "low water" indicator light(by setting an output L to 1) when the water level drops below level 5.
H.W :- 1) A four logic-signal A,B,C,D are being used to represent a 4-bit binary number with A as the LSB and D as the MSB. The binary inputs are fed to a logic circuit that produces a logic 1 (HIGH) output only when the binary number is greater than 01102-610. Design this circuit. 2) repeat problem 1 for the output will be 0 (LOW) when the binary input is less than 01112-710- Saleem Lateef
The results of each stage in a sequential logic circuit are reliant on the data that came before them. O a. On The sole input is the timing signal, or clock. be familiar with OC data from previous work. There are no other places we can turn to seek details.
I need the answer as soon as possible