An ideal gas refrigeration cycle using air as the working fluid operates between the pressure limits of 80 kPa and 280 kPa. Air is cooled toTB35°C before entering the turbine. The lowest temperature of this cycle is (Hint:k-1PBkTAPA0°C11°C24°C-58°C-26°CO O O O

Answered: Image /qna-images/answer/8285b806-64f9-4bcc-bb1f-7df2dd9c3129.jpg

An ideal gas refrigeration cycle using air as the working fluid operates between the pressure limits of 80 kPa and 280 kPa. Air is cooled to k-1 TB 35°C before entering the turbine. The lowest temperature of this cycle is (Hint: k TA P. 0°C 11°C 24°C -58°C -26°C ドに O O O O

An ideal gas refrigeration cycle using air as the working fluid operates between the pressure limits of 80 kPa and 280 kPa. Air is cooled to k-1 TB 35°C before entering the turbine. The lowest temperature of this cycle is (Hint: k TA P. 0°C 11°C 24°C -58°C -26°C ドに O O O O

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The refrigerator in the diagram below uses R-134a as its working fluid Vapor-Compression Cycle and operates with P = 140 kPa and x, at the outlet of the evaporator, and P3 = 800 kPa and x3 = 0 at the outlet of the condenser. Complete a thermodynamic analysis of the system assuming ideal operation of the compressor. Adding an isentropic efficiency of nc = 75% for the compressor, repeat the analysis for the real system. Compare the coefficient of performance for the ideal system versus that of the real system and the Carnot system where TH= 25 °C and TL = -10 °C. Condenser 3 Wnet Valve Compressor 4 Evaporator 1
A simple vapour compression refrigeration system using R-134a as a refrigerant operates between an evaporator temperature of - 10 °C and a condenser temperature of 34 °C. The refrigeration capacity is 7 TR. The liquid leaving the condenser is saturated, and the compression process is isentropic. Draw the cycle on a p-h diagram and determine: a) the refrigerant flow rate. (b) the power required to run the compressor in kW. c) the heat rejected at the condenser in 1 kW. (d) the COP of the system.
An ideal gas refrigeration cycle with a pressure ratio of four uses air as the working fluid. Air enters the compressor at 100 kPa and 0°C and the turbine at 50 °C. Determine (a) the temperature at the turbine exit, (b) the heat removed per unit mass of the air, and (c) the COP of the cycle. Use constant specific heat for air at room temperature with cp = 1.005 kJ/kg.K and k = 1.4.
In the given figure, water flow at a rate of 200 L/s in an friction less pipe. The inlet diameter at point 1 is three times bigger than the outlet at point2. If the water Speed at point 2 is 4m/s determine a) the diameter at the inlet of the pipe b) The water speed at point 1 c) the pressure difference between point 1 & 2.
A simple vapor compression cycle uses ammonia as a refrigerant. The vaporizing and condensing temperature are -20°C and 35°C, respectively. The system is to be used in producing 10,000 kg of ice at -15°C from water at 25°C in 25 hours. The specific heat of ice is 2.094 kJ/kg-K and the heat of fusion is 335 kJ/kg. Assume that there are 30 percent losses of the heat to be absorbed from the water. Compute the heat rejected in the condenser in kW. (Use h₂ = 1735 kJ/kg)
Consider a refrigrator that operates on the vapor compression refrigeration cycle with R-134a as the working fluid. The refrigerant enters the compressor as saturated vapor at 70 kPa, and exits at 1200 kPa and 90°C, and leaves the condenser as saturated liquid at 1200 kPa. The coefficient of performance of this refrigrator is
An Ericsson cycle operates on 0.75 lbm of oxygen from 60 psia and 1200°F at the beginning of isothermal expansion process to the lower temperature limit of 200°F. If the isothermal expansion ratio is 3, compute QA, QR, WNET, e, and Pm.
An air-standard cycle with variable specific heats is executed in a closed system with 0.0055 kg of air and consists of the following three processes: 1–2 v = Constant heat addition from 95 kPa and 17°C to 380 kPa 2–3 Isentropic expansion to 95 kPa 3–1 P = Constant heat rejection to initial state Use data from tables. Determine the thermal efficiency. The thermal efficiency is %
Refrigerator 1 simulates an ideal refrigerator and therefore operates on a Carnot cycle using R-134a as the refrigerant at a flow rate of 1.4 kg/sec. The condensing and evaporating temperatures are 30 °C and -10 °C, respectively. To assess the performance of Refrigerator 1, you must submit the report. of the project with the following information: Enthalpies corresponding to the states indicated in the cycle (1, 2, 3 and 4); 1.a. The cooling rate (QL); 1.b. The work provided to the fluid by the compressor; 1.c. The work generated by the turbine; 1.d. The condenser heat rejection rate (QH); 1e. The coefficient of performance of the cycle;
A refrigerator uses refrigerant-134a as the working fluid and operates on an ideal vapor compression refrigeration cycle between 0.18 and 0.7 MPa. The mass flow rate of the refrigerant is 72.4 g/s. Determine the power input to the compressor (in kW). Do not answer in image format
Thermodynamic