An engine speed ratio working with the ideal Brayton's frame is 10. Air passes through the engine with a flow rate of 60 kg/min. The heat in the conversion device unit is 500 kW and the draft air is 2 0.07 MPa and the data is 73 K. What is the thermal efficiency if the specific heats of the room have a constant acceptance level? answer

An engine speed ratio working with the ideal Brayton's frame is 10. Air passes through the engine with a flow rate of 60 kg/min. The heat in the conversion device unit is 500 kW and the draft air is 2 0.07 MPa and the data is 73 K. What is the thermal efficiency if the specific heats of the room have a constant acceptance level? answer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

9-11 Jet Porpulsion - Applied Thermodynamics A turbojet is flying with a velocity of 900 ft/s at an altitude of 20,000 ft, where the ambient conditions are 7 psia and 10°F. The pressure ratio across the compressor is 13, and the temperature at the turbine inlet is 2340 R. Assume ideal operation for all components and constant specific heats for air at room temperature. The properties of air at room temperature are cp = 0.24 Btu/lbm·R and k = 1.4. Question: Determine the pressure at the turbine exit. In psia
Need correct answer neat and clean with proper explanation
pls answer all i will give thumbs up if it is right
3. An engine working on the Otto Cycle has a compression ratio of 10/. At the beginning of the compression stroke the temperature of the air is 30°C. After the addition of heat constant volume the temperature of the air rises to 1100 °C. Find the heat supplied, heat rejected & the net work done per kilogram of air in the cylinder. What is the efficiency of the cycle?
I need answer typing clear urjent
Q2/ The compression ratio of a diesel engine is 20, and cut-off occurs at 5% of the stroke. Calculate the air-standard efficiency.
What’s the answer for this please ?
Q3// Answer A or B All The plant capacity factor of power plant 50%, the peak load is 30MW, the load factor is 60% and plant use factor 80%. Find: the daily output power and the plant reserve capacity. B// What are the methods of draught in cooling towers. Demonstrate them with drawings. What is the relationship between the cooling tower and condenser.
10:38 5.5 In an air standard Otto cycle the maximum and minimum temperatures are 1400 and 15°C. The heat supplied per kilogram of air is 800 kJ. Calculate the compression ratio and the cycle efficiency. Calculate also the ratio of maximum to minimum pressures in the cycle. All 60% (5.27/1: 48.5%; 30.65/1) 5.6 A four-cylinder petrol engine has a swept volume of 2000 cm³, and the clearance volume in each cylinder is 60 cm³. Calculate the air standard cycle efficiency. If the introduction conditions are I bar and 24 °C, and the maximum cycle temperature is 1400 °C, calculate the mean effective pressure based on the air standard cycle. (59.1%: 5.28 bar) 5.7 Calculate the cycle efficiency and mean effective pressure of an air standard diesel cycle with a compression ratio of 15/1, and maximum and minimum cycle temperatures of 1650 °C and 15°C respectively. The maximum cycle pressure is 45 bar. (59.1%; 8.38 bar) 5.9 5.8 In a dual-combustion cycle the maximum temperature is 2000°C and the…
i need the answer quickly
QUESTION I Figure 1 shows cylinder block and piston of a reciprocating engine run with diesel fuel. The engine has displacement volume of 3000 cm and has clearance volume. Consider that the engine is a four-cylinder and four-stroke operates on the Diesel cycle with a compression ratio of 18 and cutoff ratio of 2. The pressure and temperature of air is at the beginning of the compression process is dependent on local ambient condition. Using constant specific heats at 500 K: i) decide working condition at the beginning of the compression process and calculate all the working temperature and pressure at all points on P-V diagram for the engine, ii) determine the net work output and the thermal efficiency, iii) determine the mean effective pressure, iv) develop expression of Power (P) as a function of rotational speed (N), and v) plot graph of Power versus Engine speed (RPM) for the above engine from 0 – 4500 rpm. Please provide complete table of Power versus Engine speed. What is the…
With complete and clear units/conversion factors. Box your final answer and round to the nearest 2 decimal places. Thank you