1-In Airbus330 aircraft are used: a - Axial compressor b- centrifugal compressor 2-In Cessna 425 aircraft are used: a - Axial compressor b- centrifugal compressor 3-In Leduc 022 aircraft are used: a - centrifugal compressor b- Axial compressor

Q: list the most popular cars, what they cost, and if they are gas, electric, or hybrid cars for:…

A: The most popular 5 car models for each of the car company is provided below. Toyota: Toyota…

Q: Magnetic cooling can attain a temperature of roughly 0.05 K. In this technique, a high magnetic…

A: solution provided in attachment

Q: n's Law of Motion odynamics mples (situational or not) from e

A: To give: The summary of Newton's Laws of Motion and Thermodynamics, with some examples.

Q:

A: from the given options, it seems option 1 is correct

Q: Define the term form factor?

A: Generally, the word Form factor is defined for the surface finish and tolerance provided over any…

Q: Prove please!

A:

Q: Thank you

A: given : t = 6.07mm = 0.00607 m F = 38.9 KN = 38900 N τ = 54.4 MPa = 54.4 x 106 N/m2

Q: can I have FBD for this?

A:

Q: A hydraulic press is used to apply 500 lbs of force to press fit an assembly. The cylinder has a 2"…

A: Given:The force applied by the hydraulic press, The diameter of the piston, The diameter of the rod,…

Q: If a car weighing 2400 lbs is able to go 1000 ft up a mountain incline whose angle of inclination is…

A: Given data: Weight of car = 2400 lbs                      Distance which car moves up the incline =…

Q: (3) In Sample Problem 15.04, the constant"kappa" is *

A:

Q: ptotic  relationship?

A: Power:- Power is the amount of work done in a given amount of time or the rate at which work is…

Q: Hi could you also please give the solution to d, e, f

A: As per the guidelines we are subjected to solve only 3 sub parts at a time. Please repost the same…

Q: Which is the "noise"?

A: We can produce sound by creating some vibration with objects.

Q: The beam has a rectangular cross section and is subjected to the loading shown. Determine the state…

A:

Q: The middle of the narrative tells

A: The middle of the narrative tells the road to climax.

Q: What's the worst car ever made?

A: Given Data⇒ worst car Problem statement⇒ Problem says What's the worst car ever made?

Q: Describe the work done is proportional to the force applied (F ) and the distance traveled (s).

A: We know that,Work Done =Force × DisplacementW = F × s From the above equation, If…

Q: "If we push the book on the table, it stops after sometime. Why?"

A: If we push the book on the table, then the book will get some speed. but after some time the book…

Q: Distinguish between the Surface Loads and the Distributed Loads?

A: Load is defined as an external force or a couple to which a member is subjected during its…

Q: a) Given is a penstock with deflection and subsequent cross-section reduction. Determine the…

A: Find the pressure loss.

Q: So what are the correct answers

A: Explanation: If we consider a system that loses heat δQ at temperature T. Since, In this case the…

Q: Block of 10 N, orbit in polar coordinates r = (3t ^ 2) m and e = (0.5t) rad parametric It moves…

A:

Q: Explain three pages of laminar flow with the drawing

A:

Q: trenching  machine design and modeling.  Each concept must have an introduction and design…

A: Equipment that is portable and built for small-scale trenching operations is the tiny excavator…

Q: Q2/ Fill in the blanks with suitable phrases or terms:- 1- The typical composition of austenitic…

A: 1. The typical composition of austenitic stainless steel is            Note :- you have posted…

Q: ACCURATELY

A: We have given ACCURATELY

Q: horwalizing 1) Machinability of low carbon steels improved by: high carbon steel improved by…

A: Heat treatment processes are used to get the desired properties in the metals.

Q: Manufacuring Processes An electro chemical machining (ECM) operation is employed too cut a square…

A: Write the given data:

Q: why is the length of the wire use in finding the centripetal force instead of the radius?

A:

Q: Q2: Select any one casted component shown in the figure which is made up of alloy material and used…

A: I will select second one i.e  spiral bevel gear. Alloys used in making gears is zinc alloys  or…

Q: A pair of forces acting directly on the material to reduce in its length are called   Select one:…

A: Solution:

Q: How did you arrive at the 115?

A:

Q: For step one, I got the same values but negative

A:

Q: When using a specific mass of an ideal gas with a specific pressure inversely proportional to the…

A: Ideal gas equation is given by, PV = mRT where, P = absolute pressure of gas V = volume of gas m =…