An electric heater supplies energy to a 55.0 g block of Al. The temperature was originally 22.5 °C and final temperature is 30.1°C. Compute the joules of energy that the heater supplies. Molar heat capacity of Al is 24.35 (J mol¯1°C-1). Molar mass of Al = 26.98 g/mol 237.61 J 3.38 x 102 J 33.752 J 158.4 j

An electric heater supplies energy to a 55.0 g block of Al. The temperature was originally 22.5 °C and final temperature is 30.1°C. Compute the joules of energy that the heater supplies. Molar heat capacity of Al is 24.35 (J mol¯1°C-1). Molar mass of Al = 26.98 g/mol 237.61 J 3.38 x 102 J 33.752 J 158.4 j

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

When a piece of unknown metal weighing 63.40 grams, and at a temperature of 87.80 °C, is placed in a calorimeter containing 264 g water at 20.10 °C, the temperature increases to 21.40 °C. As the heat capacity of the calorimeter is 194.20 J K¯¹, what is the specific heat of the unknown metal in J g¯¹ K¯¹?
An electrical heater is used to add 19.75 kJ of heat to a constant-volume calorimeter. The temperature of the calorimeter increases by 4.76°C. When 2.00 g of methanol (CH3OH) is burned in the same calorimeter, the temperature increases by 10.92°C. Calculate the molar heat of combustion for methanol (in kJ).
As a system increases in volume, it absorbs 52.0 J of energy in the form of heat from the surroundings. The piston is working against a pressure of 0.597 atm. The final volume of the system is 58.6 L. What was the initial volume of the system if the internal energy of the system decreased by 106.2 J? Volume = L
Calculate the energy required to heat 1.80kg of ammonia from 21.5°C to 41.0°C . Assume the specific heat capacity of ammonia under these conditions is ·4.70J·g−1K−1 Round your answer to 3 significant digits.
the molar heat capacity of iron is 25.10 J mol –1 K–1 . A 25.0 g ball is heated until it is glowing red (to a temperature of 400.°C). It is dropped into a 50.0 mL container of water at 25.0°C. If the density of water is 0.997 g mL–1 , and the molar heat capacity of water is 4.186 J g–1 K–1 , what temperature (in K) will the ball and water equilibrate to? A) 338 B) 300 C) 317 D) 359 E) 342
A chemist carefully measures the amount of heat needed to raise the temperature of a 0.88 kg sample of C,H0, from 35.8 °C to 51.4 °C. The experiment shows that 2.34 × 10* J of heat are needed. What can the chemist report for the molar heat capacity of C,H00,? Round your answer to 2 significant digits. |J-mol 1 - 1 •K х10
A 56.1 g sample of polystyrene, which has a specific heat capacity of 1.880 J-g °C-1 is put into a calorimeter (see sketch at right) that contains 250.0 g of water. The temperature of the water starts off at 24.0 °C. When the temperature of the water stops changing it's 29.8 °C. The pressure remains constant at 1 atm. Calculate the initial temperature of the polystyrene sample. Be sure your answer is rounded to the correct number of significant digits. °C thermometer. insulated container water sample. a calorimeter 區 OU Ar
A chemist carefully measures the amount of heat needed to raise the temperature of a 1.65kg sample of C9H10O2 from 25.9°C to 37.9°C. The experiment shows that 3.09 X 104J of heat are needed. What can the chemist report for the molar heat capacity of C9H10O2? Round your answer to 3 significant digits. = J * mol-1 * K-1
A chemist measures the enthalpy change AH during the following reaction: 2 KCl(s) + 302(g) →2 KClO3(s) AH=78. kJ Use this information to complete the table below. Round each of your answers to the nearest kJ. reaction ΔΗ ㅁ x10 2K C103 (s) → 2KC1(s) + 302(g) KCIO, (s)-KCI(s) + 0,(s) 3 KCI(s)+0, (g)KCIO, (s) kJ kJ 1 5
A bomb calorimeter, or constant volume calorimeter, is a device often used to determine the heat of combustion of fuels and the energy available from foods. Since the "bomb" itself can absorb energy, a separate experiment is needed to determine the heat capacity of the calorimeter. This is known as calibrating the calorimeter. In the laboratory a student burns a 0.461-g sample of 2-naphthylacetic acid (C12H1002) in a bomb calorimeter containing 1150. g water. The temperature increases from 24.70 °C to 27.20 °C. The specific heat capacity of water is 4.184 J g1 oC-1. The combustion enthalpy is -5779 kJ/mol 2-naphthylacetic acid. C12H1002(s) + 27/2 02(g) –→12 CO2(g) + 5 H20(1) A,H° -5779 kJ/mol Calculate the heat capacity of the calorimeter. heat capacity of calorimeter= orc J/C
A chemist carefully measures the amount of heat needed to ralse the temperature of a 1.48 kg sample of C,H,0, from 32.9 °C to 50.0 °C. The experlment 4-8 2 shows that 4.02 x 10* J of heat are needed. What can the chemist report for the molar heat capacity of C,H,0,? Be sure your answer has the correct number of significant digits.
A student is attempting to determine the heat capacity of a Styrofoam cup calorimeter by pouring hot water into a Styrofoam cup containing cold water. The student determined the mass of the cold water to be 21.2455 g and its initial temperature to be 20.36 °C. The mass of the hot water was 24.2646 g and its initial temperature as 34.54 °C. The final temperature of the water after mixing was determined to be 24.57°C. The specific heat capacity of the water is 4.184 J/(g•°C). What is the heat capacity of the Styrofoam cup calorimeter? Assume the temperature of the calorimeter is the same temperature as the cold water. 4.184 J/°C 132.5 J/°C