An Ammonia refrigerant vapor compression system is utilized as an air-cooled water chiller. It is operating at a condenser temperature of 40°C and an evaporator temperature of 0°C. The system develops 15 Tons of Refrigeration. Determine: a. The discharge temperature and mass flow rate of the refrigerant circulated. b. The theoretical piston displacement of the compressor. c. The theoretical compressor work. d. The heat rejected in the condenser. e. The Carnot COP and the actual COP of the cycle. f. The volume of air supplied in the condenser if it enters at 30°C and leaves at 34°C. g. LMTD and AMTD in the condenser h. The water flow rate of the chiller if it enters the evaporator at 10°C and

An Ammonia refrigerant vapor compression system is utilized as an air-cooled water chiller. It is operating at a condenser temperature of 40°C and an evaporator temperature of 0°C. The system develops 15 Tons of Refrigeration. Determine: a. The discharge temperature and mass flow rate of the refrigerant circulated. b. The theoretical piston displacement of the compressor. c. The theoretical compressor work. d. The heat rejected in the condenser. e. The Carnot COP and the actual COP of the cycle. f. The volume of air supplied in the condenser if it enters at 30°C and leaves at 34°C. g. LMTD and AMTD in the condenser h. The water flow rate of the chiller if it enters the evaporator at 10°C and

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A two-evaporatoor compression refrigeration system like that in the Figure below uses refrigerant-134a as the working fluid. The system operates evaporator 1 at 30 psia, evaporator 2 at 10 psia, and the condeser at 180 psia. The cooling load for evaporator 1 is 9000 Btu/h and that for evaporator 2 is 24,000 Btu/h. Determine the power required to operate the compressor and the COP of this system. The regrigerant is saturated liquid at the exit of the condenser and saturated vapor at the exit of each evaporator, and the compressor is isentropic.
Can you also show the T-s and P-h diagrams? A Single Stage Vapor Compression (SSVC) refrigeration system has a cooling capacity of 6 tons. The discharge of the evaporator is at -20°C & 0.1 MPa and the discharge of the condenser is at 30°C & 1.0 MPa. Determine the following: (a) the COP of the system, (b) the Energy Efficiency Ratio in kJ/hr/W, (c) the HP/ton of the system, (d) the Refrigerating Efficiency of the system.
42. Refrigerant-12 enters the condenser of a vapor-compression refrigera- tion system at 175 psia and 140°F and leaves as saturated liquid at 120°F. Mass flow rate of the refrigerant is 4.8 lbm/min. The heat is rejected to the surrounding air, which is at 90°F. Determine: (a) Heat rejection rate, Btu/hr. 22 (b) Separate the overall entropy changes per hour (Freon and sur- roundings). 23/
Superheated steam from the boiler expands in the turbine from inlet pressure p₁ of 50 bar and temperature 7 of 487 °C to condenser pressure p2 of 18 kPa. In the condenser, the steam condenses to saturated water. The isentropic efficiency of the turbine ns is 78.0 %. The mass flow of steam 9m,h is 140 kg/s. In the boiler, heat flow rate to the circulating fluid (water/steam) is 458 MW. Read from h,s-diagram and calculate: 1. Enthalpy of the superheated steam h kJ/kg (with zero decimal accuracy) 2. Enthalpy of the steam at turbine outlet after isentropic expansion h₂s kJ/kg (with zero decimal accuracy) 3. Enthalpy of the steam at turbine outlet h₂ kJ/kg (with zero decimal accuracy) 4. Turbine power Pt MW (with one decimal accuracy) 5. Steam content at the turbine outlet X2 kJ/kg (with two decimal accuracy) 6. Enthalpy after condenser h3 kJ/kg (with zero decimal accuracy) 7. Thermal power of condenser Qc 8. Thermal efficiency of the plant n MW (with one decimal accuracy) % (with one…
Question 3 In a vapour-compression refrigeration system, refrigerant - 134a enters the compressor superheated at 200 kPa and - 5 °C. The refrigerant enters the condenser at 1.4 MPa and 75 °C, and exits at 1.4 MPa as a saturated liquid. There is no significant heat transfer between the compressor and its surroundings, and the refrigerant passes through the evaporator with a negligible change in pressure. If the refrigerating capacity is 105 kW, represent the cycle on a T-s diagram and determine: a) the mass flow rate of the refrigerant in kg/s, b) the power input to the compressor in kW, c) the coefficient of performance, and (2) d) the isentropic compressor efficiency
An ammonia refrigerating system has a load of 250 kW and operates at a condensing pressure of 1400 kPa and an evaporating temperature of -20°C. The refrigerant exits at the evaporator with a 5- degree superheat. The vapor enters the compressor suction at 10-degree superheat. The compressed vapor is discharged from the compressor at the condensing pressure and 150°C. The refrigerant exits the condenser as saturated liquid. a. State the enthalpies at each point: Point enthalpy kJ/kg h kJ/kg kJ/kg h2 kJ/kg h3 kJ/kg h4 Answer: kg/sec b. Calculate the mass flow of refrigerant Answer: kW C. Determine the size of the motor drive if the mechanical efficiency of the motor- compressor is 77%. Answer: kW Calculate the total heat rejected in the condenser. d. Determine the refrigerating efficiency of the system. Answer: е.
Determine the cooling capacity and the coefficient of performance of the air conditioning system?
Refrigerant 22 is the working fluid in a Carnot vapor refrigeration cycle for which the evaporator temperature is -30°C. Saturated vapor enters the condenser at 36°C, and saturated liquid exits at the same temperature. The mass flow rate of refrigerant is 10 kg/min. Determine the power input to the compressor, in kW, (A) 6.72 (B) 5.35 7.76 3.51 D
11. A vapour compression refrigeration plant uses ammonia. The compressor takes vapour from the evaporator at 207.7kPa and -8°C and delivers to the condenser at 1470kPa and 113°C. The temperature of the liquid leaving the condenser at a rate of 12kg/min is 38°C. Calculate: (a). the dryness of the refrigerant entering the evaporator (b). the cooling load (c). the power to the compressor (d). coefficient of performance (e). plant capacity
Please help!!!! Refrigerant 22 enters the compressor of an ideal vapor-compression refrigeration system as saturated vapor at -30°C with a volumetric flow rate of 10 m3/min. The refrigerant leaves the condenser at 19°C, 9 bar. Determine: (a) the magnitude of the compressor power, in kW. (b) the refrigerating capacity, in tons. (c) the coefficient of performance. (d) the rate of entropy production for the cycle, in kW/K. Answer for part (a): 52 kW Answer for part (b): 59 tons Answer for part (c): 3.98 Please answer part also d! That's the part I also need. Thank you!
Refrigerant 22 is the working fluid in a Carnot vapor refrigeration cycle for which the evaporator temperature is -30°C. Saturated vapor enters the condenser at 36°C, and saturated liquid exits at the same temperature. The mass flow rate of refrigerant is 10 kg/min. Determine the quality of refrigerant at inlet of compressor, (A) 0.9430 B 0.6931 C 0.7931 D 0.8931