An aluminum tube with the cross section shown has a constant wall thickness of 2 mm. A torque T = 400 N·m is applied to the tube. Use G= 28 GPa What is the area of the tube? What is the total length of the median line? The shearing stress value will be The angle of twist result is

Q: A beam with the cross section geometry and dimensions as shown in the figure and parameter table is…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: The ultimate stress for the hitch ball is 60,000 ksi. (Capacity) The advertisement information is…

A:

Q: The solid shaft shown in the figure below is fixed at one end and has a lever at the other. The…

A:

Q: A hollow tubular shaft will be used between the engine and the propeller of the boat as shown in the…

A: given data;outer diameter (do)=74mmthickness (t)=6mmengine power(P)=10KWspeed (n)=694rpmstress on…

Q: In a cruise ship, a liferaft is hanged by suspending it with a thick metallic cable attached to both…

A: Given,  Tension in the cable , T = 40 KN Maximum allowable shear stress  = 50 * 106 Pa

Q: A drill drills a hole in a leg of a furniture. Uses a hand-operated drill with a bit of diameter…

A: Given Data Diameter of drill bit is : d=5.79 mm=5.79×10-3 m Resisting torque is : T=0.36 N·m…

Q: 3. A tubular aluminium bar (G = 30 GPa) of square cross-section as shown below, with outer…

A: To Find : The minimum required wall thickness Given : The allowable shear stress is The torque is…

Q: torque that will cause a maximum shear stress of 10 000 psi. Use G = 4x 106 psi for aluminum. e-4…

A: Solnn:- in a given figure  Sear stress=10000 psi G= 4×10^6 psi Now, enclosed area Am= π\2  ×  r^2 +…

Q: 2. A tube is made of aluminum (G = 24 GPa ) and has a rectangular cross section as shown in figure.…

A:

Q: The first law for an open system is set up. Q12+... AH+AEkin+AEpot- Which term goes in the missing…

A: Work ( W) is going in the missing place in above equation of the first law of thermodynamics for an…

Q: A shaft with splines of a diameter of 50 mm, as shown in the figure below, transmits a torque of…

A: Given: The diameter of the shaft, d’ = 50 mm The torque, T = 1600 N.m The minimum diameter of the…

Q: A solid shaft made of aluminum alloy (E=70 Gpa, v=0.33). The diameter of the shaft is 25 mm, and…

A: Introduction The strain represents the change in dimension of the body under the loading compared to…

Q: Find the maximum shear stress and rate of twist for an applied torque Mi for the section shown in…

A: given; where;⇒t=thickness⇒a and b are dimensions. ⇒t<<a,b

Q: Please please try to solve it asap it is too urgent. A solid round bar, 25 mm in diameter, has a…

A:

Q: 2. A hollow generator shaft of 180-mm outer diameter and 120-mm inner diameter carries a torque T 40…

A:

Q: fofits length as show ar is dz= 3.0 in. and afts material is steel w

A:

Q: 3- A steel shaft in a conveyor transmits 30 hp of power at 5 Hz. Determine the smallest safe…

A:

Q: A steel circular tube is subjected to torsion by torques T applied the ends as shown below. The bar…

A:

Q: espectively, is fixed on one end and torsional forces (T=10 kN.m) are applied at joining points as…

A: givensolid shaft made of steel aluminium and bronze length of each segments L=3m=3000mmtorsional…

Q: A hollow tubular component is made of Steel having a Young's modulus of 205 GPa and yield strength…

A: Given Data⇒ Tensile load (F)=38 KN External diameter of the hollow tubular component is d2=45 mm…

Q: A prismatic wing box is constructed of two cylindrical tubes (each of thickness welded to top and…

A:

Q: 0.75 in 0.75 m The torque T = 300 KN.m. The tube thickness t = 10 mm and length L = 1.3 m. and G =…

A: Answer: (a) The average shear stress in the tube: 3.147 MPa. (b) The angle of twist: 1.3845E-4.

Q: Q-3 Two solid shafts of different material are rigidly fastened together and attached to rigid…

A:

Q: 2 in in 1 in 8 3 in 3 in 3100 in in

A:

Q: tube subjected to pr times the inner radi hear strain in the tu ner surface? allowable rate of tv

A:

Q: A motor driving a solid circular steel shaft transmits 30 kW to a gear at B (as shown). The…

A: Here is the solution for the above question.

Q: The circular shaft shown is subjected to an axial force P at its free end and a compressive force of…

A: Answer: The maximum allowable value of load P is 11.66 kips.

Q: 1. Compute the maximum shearing stress and deflection of a helical spring made from bronze…

A: Given: The number of turns is n=20. The diameter of wire is d=0.5 in. The mean radius is r=3 in. The…

Q: as the following standard

A: given data shaft dia = 60 mm length of key = 50 mm b = 18 mm h= 11 mm torque T = 350 x 1000 N-mm…

Q: b) The following diagram represent a shaft composed of three segments and fastened to rigid…

A: According to the given data TC=300 N.m TD=700 N.m segment Material Diameter(mm) Length(m) Shear…

Q: The outer diameter of the solid steel pipe shown in the figure is 25 mm. If the pipe is fixed at…

A: Principle Stresses : planes in which plane shear stress is zero are known as principle plane and…

Q: 40 N.m Da 0.5 m 280 N.m 150 N.m 2 0.3 m 0.4 m

A:

Q: Calculate the shearing stress in pin A of the bulldozer if the total forces acting on the blade are…

A: Two forces acting on the blade is 8K and 4K We can find the shear stress in each pin

Q: Find the max shear stress in a 200mm tall, 150mm wide rectangular cross section using the…

A:

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational kinetic energy in a body. For instance, in an automobile, the power transmission shaft is a body that is always under rotation due to the external torque acting on it, this torque is created by the engine.