An acetal disk 5mm thick by 25mm diameter is used as a cover plate in a mechanical loading device. If a 20kN compressive load is applied to the flat surfaces of the disk, calculate the disk's resulting diameter while under load.

An acetal disk 5mm thick by 25mm diameter is used as a cover plate in a mechanical loading device. If a 20kN compressive load is applied to the flat surfaces of the disk, calculate the disk's resulting diameter while under load.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PROBLEMS 203. During a stress-strain test, the unit deformation at a stress of 5000 psi Wap ODserved to be 0.000167 in./in. and at a stress of 20,000 psi it was 0.000667 in./in. If the proportional limit is 30,000 psi, what is the modulus of elasticity? What is the stress corresponding to a strain of 0.0002 in./in.? Would these re- sults be valid if the proportional limit were 18,000 psi? Explain. E = 30 X 106 psi; S 6000 psi %3D Ans. 204. A uniform bar of length L, cross-sectional area A, and weight W is sus- WL If pended vertically from one end. Show that its total elongation is & = 2AE wL? its weight per unit volume is w, show also that & 2E A steel rod having a cross-sectional area of sq in. and a length of 600 ft is suspended vertically. It supports a load of 5000 lb at the lower end. If steel 30 X 106 psi, find the total elongation in the rod. Ans. 8 = 2.64 in. 205 weighs 490 lb/cu ft and E Hint: Use the result of Prob. 204. steel wire 30 ft long, hanging vertically, supports a…
A composite column is formed by placing a steel bar 20 mm diameter and 200 mm long, inside an alloy cylinder of the same length whose internal and external diameters are 20 mm and 25 mm respectively. The column is then subjected to an axial load of 50 kN. Modulus of elasticity for steel and alloy is 200000MPa and 70000MPa respectively. Which of the following gives the stress in the steel bar? a. 132.98 MPa b. 46.54 MPa c. 74.80 MPa d. 166.23 MPa
I need the answer as soon as possible
A cylindrical specimen of some metal alloy having an elastic modulus of 101 GPa and an original cross-sectional diameter of 3.6 mm will experience only elastic deformation when a tensile load of 2430 N is applied. Calculate the maximum length of the specimen before deformation if the maximum allowable elongation is 0.41 mm. i mm
The solid circular drill rod AB is made of a steel that is assumed to be elastoplastic with τY = 22 ksi and G = 11.2 × 106 psi. Knowing that a torque T = 72 kip·in. is applied to the rod and then removed, determine the maximum residual shearing stress in the rod. The maximum residual shearing stress in the rod is ksi.
If length of rod is 2 m and a radius of 20 mm is made of high-strength steel. The rod is subjected to a torque T, which produces a shear stress below the proportional limit. If the cross section at one end is rotated 45 degrees in relation to the other end, and the shear modulus G of the material is 90 GPa, calculate the amount of applied torque?
Problem: A steel rod with a cross-sectional area of 180 mm2² is stretched between two fixed points. The tensile load at 25°C is 3,600N. Assume thermal coefficient equal to 11.7 x 106 mm/ (mm°C) and E= 200 GPa. a. What is the temperature at which the stress will be zero? b. What is tthe temperature at which the compressive stress will be 48 MPa?
COMPLETE SOLUTIONS PLEASE WITH FBD
A drill rod with a diameter of 10 mm is made of high-strength steel alloy with a shear modulus of 80 GPa. The rod is to be subjected to a torque T. What is the minimum required length L of the rod so that the cross section at one end can be rotated 90° with respect to the other end without exceeding an allowable shear stress of 300 MPa?
Q.3 The compressive strength of (Ø25×25) cm cylinder is 30 MPa at an age of 21-day, determine the direct tensile strength at the age of 7-day.