An acb sequence balanced three-phase Y-connected source supplies power to a balanced three-phase A-connected load with an impedance of 18+ j15 2/6. The sourcevoltage in the b-phase is 260/-55°V. The line impedance is 1+j102/6. Use the single-phase equivalent circuit for the a-phase to find the current in the a-phase of theload.

The question is about per phase equivalent circuit to find out phase current.

An acb sequence balanced three-phase Y-connected source supplies power to a balanced three-phase A-connected load with an impedance of 18+j15 02/. The source voltage in the b-phase is 260/-55°V. The line impedance is 1+j102/6. Use the single-phase equivalent circuit for the a-phase to find the current in the a-phase of the load.

An acb sequence balanced three-phase Y-connected source supplies power to a balanced three-phase A-connected load with an impedance of 18+j15 02/. The source voltage in the b-phase is 260/-55°V. The line impedance is 1+j102/6. Use the single-phase equivalent circuit for the a-phase to find the current in the a-phase of the load.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: What are the RMS line current at load 1 and 2 respectively?
Phase Qz/ The eas Voltages at the terminal of abalan ced Y connected load is VAN=12o 28. Each Phase of the load consist of lo 230° .Find the active & Reactive and Complex Power Per-Phase then find the total Powers For three Phase load.
Given at the load: Vioond = 452-25° VRMS, 452-25° VRMS, Iload What are the real and reactive power and power factor at the load? Exclude the units. real power: reactive power: power factor: Iload-10-25 ARMS what type of impedance is seen at the load? R. L. or Ch
Pz:- The of abalanced Y connected load is- Each phase of the load cousist of loL30 s2 Find the Line Voltages at the terminat actives Reachive and somflex Power Per Phase then Find the total Powers For Heree phase load. VAB =10010for 4
A single phase, unity power factor load takes 90 Amps at 10 kV. Using a base voltage of 65 kV and base kilovolt amperes of 4475 kVA. Find the base current, base impedance, base power, per unit current and per unit voltage of the load.
Determine the value of the impedance, Z₁, that causes maximum power transfer in the circuit shown in Figure Qlc. 52 j24n -j12.35n (V₂) j2403 j24n Figure Qle B
2. A single-phase a.c. distributor AB is fed from end A and has a total impedance of (0-2 + j 03) ohm. At the far end, the voltage V = 240 V and the current is 100 A at a p.f. of 0-8 lagging. At the mid-point M, a current of 100 A is tapped at a p.f. of 0-6 lagging with reference to the voltage Vy at the mid-point. Calculate the supply voltage V, and phase angle between V, and Vg- [292 V, 2-6°] a loade
solve it
Solve it please fast
Please Answer My Questions in 30 minutes i'm very needed... Please thank u...
Note: Please write and answer neatly with solutions, thank you!
A three-phase feeder supplies two loads A and B at 380 V (Figure 2).Find the impedance of load A of (55 + j89) ohms and that of load B of(90 + j66) ohms. Ordered as currents in phases A that feed the twoloads, and as currents in the delta connected load.