2) A Y- connected load with an impedance of 12-j15 2 per phase in connected to a balanced A-connected 208-V, 60 Hz, three-phase, positive phase sequence supply. Determine (a) the line and the phase voltages, (b) the line and phase currents (c) the apparent, active, and reactive powers in the load. Draw the phasor diagram and the power diagram.

2) A Y- connected load with an impedance of 12-j15 2 per phase in connected to a balanced A-connected 208-V, 60 Hz, three-phase, positive phase sequence supply. Determine (a) the line and the phase voltages, (b) the line and phase currents (c) the apparent, active, and reactive powers in the load. Draw the phasor diagram and the power diagram.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Problem 2 The circuit diagram of a certain load is presented below. Determine the following: a. The power factor of the load. b. If the load is connected across a 400 Vrms source, determine the real and reactive power consumed by the load. c. From (b), determine the value of the capacitor to be placed in parallel with the load in order to improve the power factor of the load to 95% lagging. From (b), A synchronous motor is installed in parallel with the load to correct the pf. The motor is rated 5 hp operating at 60% efficiency. Assuming that the motor is running at rated power. Determine the apparent power and power factor of the motor in order to improve the load's pf to 95% lagging. 202 500 µF HI + VL -20 mH 5Ω >0.5VL m 15 mH
Three Impedances each of (9 - j18)N are connected in mesh across a three-phase 415V ac supply. Determine the phase current, line current, active power, reactive power drawn from supply. Also draw the Phasor diagram for the mesh connection and marks the Line current ,phase current line voltage and phase angle between phase current and pahse voltage. phase current (Ip) Line current real power reactive power
If the voltage and current supplied to a circuit orload by a source are˜VS = 170∠(−0.157) V ˜IS = 13∠0.28 Adeterminea. The power supplied by the source which isdissipated as heat or work in the circuit (load).b. The power stored in reactive components in thecircuit (load).c. The power factor angle and power factor.
If the load is connected to the generator thgrough an inductive line and the voltage at the load side is the same as the voltage at the terminals of the generator, which of the following must be true? O A. The reactive power is flowing from the generator to the load and from load to the generator at the same time. O B. The load is disconnected, and no power is delivered to the load. O C. The load has a poor power factor and it's absorbing too much reactive power. O D. None of the other choices are correct O E. The generator is unable to produce reactive power; therefore, the reactive power is flowing from the load to the generator.
Two relays each with 20-ohm resistance and 0.16-henry inductance are connected in series. What is the equivalent impedance?a. 20 + j102.2 ohms c. 20 + j95.32 ohmsb. 20 + j120.63 ohms d. 10 + j25.32 ohms
Describe the concept of three-phase power in electrical systems and its significance in power distribution.
A load has a leading power factor. a) Is it a capacitive or inductive load? b) Is the reactive power positive or negative? c) Repeat for a load with lagging power factor
Problem: Given wye connected source: La Ven Van Von 6-1892 A 6-j802 N 6-j8Q2 I₂ Von = 120-120° V = 120 <-240° bn where V = 1200° an a) Find the line-to-line voltage phasors for the wye connected source. b) Find the line current phasors in each of the three phases of the resistive load. c) Find the current flowing in the neutral.
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
Determine the value of the impedance, Z₁, that causes maximum power transfer in the circuit shown in Figure Qlc. 52 j24n -j12.35n (V₂) j2403 j24n Figure Qle B
Three identical Y-connected loads, each having a resistance of 20 22 in parallel with an inductor, are connected to a three phase supply of 400 V and 50 Hz frequency. The power absorb by the load is 8 kW and power factor at the load is 0.9919. (i) Determine the current that flows through the inductor. Please state the assumptions used to solve the question. Calculate load inductance in Henry (H).
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three- phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT RO- SO TO IR Is IT U₁-380 V CARGA 1 P₁ =950 W cos p1=0,5 ind. CARGA 2 P₂=1.140 W cos p₂=1 CARGA 3 P3=760 W cos p3=0,5 cap.